Data acquisition is a critical task for various embedded applications where monitoring and control is needed. Measurement boards are ideal solutions for converting data from analog to digital world and versa-visa.
12-bit digital-to-analog converter MCP4921 features an optional 2x buffered output and SPI interface. The board provides high accuracy and low noise performance for industrial applications where calibration or compensation of signals, such as temperature, pressure and humidity, are required. Board is compatible with all mikroElektronika development boards and provided DIP switches enable you to route SPI lines to desired pins on IDC10 header.
$18.00
The three-axis accelerometer board features a small, thin, low-power, complete 3-axis accelerometer ADXL330 with signal conditioned voltage outputs, all on a single monolithic IC. It measures acceleration with a minimum full-scale range of ±3 g and has 5V voltage level. It can measure static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion, shock or vibration. ADXL330 is used in cost-sensitive, low-power, motion- and tilt-sensing applications such as: mobile devices, gaming systems, disk drive protection, image stabilization, sports and health devices, etc.
$26.90
The Potentiometer Board is an effective and low-cost solution for testing analog inputs on the prototype board. Connect your device to the Potentiometer Board via the IDC10 connector. All components provided on the board are clearly marked so that there is no need for additional schematics.
$16.00
EasyADC Board includes a 12-bit Analog-to-Digital Converter (ADC) MCP3204 with 4 input channels and low-power consumption. Board features DIP switches for flexible communications pin selection. Board uses industry standard SPI communication interface. It is compatible with development boards from mikroElektronika and features convenient screw terminals for easier connections.
$24.00
ADC PROTO Board includes a 12-bit Analog-to-Digital Converter (ADC) MCP3204 that features 100k samples/second, 4 input channels and low-power consumption (5nA typical standby, 400 µA max). Board uses industry standard SPI communication interface. It is small in size and features convenient screw terminals for easier connections.
$24.00
The R/2R ladder DAC is an 8-bit Digital to Analog Converter. An 8-bit value from the microcontroller port will be converted into an equivalent analog voltage by means of the R/2R resistor network. The R/2R ladder DAC makes use of only two resistor values, but it requires 2N resistors to implement the N-bit conversion. The resistor values are in the ratio of 1:2. The R/2R DAC board output is provided with the MCP6284 operational amplifier used as a buffer in order to drive loads with current consumption of up to 20mA.
$9.00
The SHT1X Board features a digital humidity/temperature sensor SHT11. A unique capacitive sensor element is used to measure relative humidity while the temperature is measured by a band-gap sensor. A 2-wire serial interface and internal voltage regulation allow easy and fast system integration.
$26.00
The SHT1X PROTO Board features a digital humidity/temperature sensor SHT11. A unique capacitive sensor element is used to measure relative humidity while the temperature is measured by a band-gap sensor. A 2-wire serial interface and internal voltage regulation allow easy and fast system integration. Board features connection pads compatible with standard breadboards.
$24.00
The Accel SPI Board features a complete 3-axis acceleration measurement system ADXL345 with selectable measurement range of ±2 g, ±4 g, ±8 g, or ±16 g. It measures both dynamic acceleration resulting from motion or shock and static acceleration, such as gravity, which allows the device to be used as a tilt sensor. Digital output data is formatted as 16-bit twos complement and is accessible through SPI communication interface. ADXL345 is suitable for mobile device applications. Its high resolution (4 mg/LSB) enables measurement of inclination changes less than 1.0°.
$19.00
ADC Click is an accessory board in mikroBus™ form factor. It includes a 12-bit Analog-to-Digital Converter (ADC) MCP3204 that features 50k samples/second, 4 input channels and low-power consumption (500nA typical standby, 2µA max). Board uses industry standard SPI communication interface. It is small in size and features convenient screw terminals for easier connections. Board is set to use 3.3V power supply by default. Place PWR SEL SMD jumper to 5V position if used with 5V systems.
$24.00
DAC Click is an accessory board in mikroBus™ form factor. It includes a 12-bit Digital-to-Analog Converter MCP4921 that features an optional 2x buffered output and SPI interface. The board provides high accuracy and low noise performance for industrial applications where calibration or compensation of signals, such as temperature, pressure and humidity, are required. Board is set to use 3.3V power supply by default. Solder PWR SEL SMD jumper to 5V position if used with 5V systems.
$18.00
SHT11 Click is an accessory board in mikroBus™ form factor. It includes a digital humidity and temperature sensor SHT11. A unique capacitive sensor element is used to measure relative humidity while the temperature is measured by a band-gap sensor. Serial I2C interface and factory calibration, allow easy and fast system integration. Board is set to use 3.3V power supply by default. Solder PWR SEL SMD jumper to 5V position if used with 5V systems.
$26.00
