Click Boards
Filter Product By
Slide and select filter/s
Filtered by
Categories
Loading
Load more
Loading
Viewed products
3D Hall 4 Click is a compact add-on board that can detect the strength of a magnetic field in all three dimensions. This board features the SENM3Dx, a 3D Hall magnetic sensor from SENIS. It is a CMOS-integrated magnetic field sensor that allows the acquisition of all three magnetic field components at the same time and in the same spot. The sensor is equipped with on-chip EEPROM to hold initialization, calibration data, and other settings and definitions. This Click board™ makes the perfect solution for the development of a wide range of magnetic sensing, including robotics position sensing, angle measurement at the end of the shaft and out-of-shaft configurations, and many more.
3D Hall 4 Click is fully compatible with the mikroBUS™ socket and can be used on any host system supporting the mikroBUS™ standard. It comes with the mikroSDK open-source libraries, offering unparalleled flexibility for evaluation and customization. What sets this Click board™ apart is the groundbreaking ClickID feature, enabling your host system to seamlessly and automatically detect and identify this add-on board.
MIKROE-5925$169.00
H-Bridge 18 Click is a compact add-on board that controls brushed DC (BDC) and stepper motors. This board features the DRV8904-Q1, an automotive-grade multi-channel half-bridge driver from Texas Instruments, offering advanced diagnostics and protection features. The DRV8904-Q1 supports independent, sequential, or parallel motor driving modes, with each half-bridge delivering up to 1A (6A maximum current for paralleled outputs). It features an SPI interface with daisy-chain capability, eight programmable PWM generators, and comprehensive fault detection, including short-circuit, undervoltage, and thermal overload protection. Additionally, it includes a low-power Sleep mode, a fault indication pin (FLT), and dedicated test points for monitoring the connected load. H-Bridge 18 Click is ideal for HVAC flap control, LED lighting, multiple brushed DC motor systems, and solenoid actuation, where precision control and system reliability are crucial.
H-Bridge 18 Click is fully compatible with the mikroBUS™ socket and can be used on any host system supporting the mikroBUS™ standard. It comes with the mikroSDK open-source libraries, offering unparalleled flexibility for evaluation and customization. What sets this Click board™ apart is the groundbreaking ClickID feature, enabling your host system to seamlessly and automatically detect and identify this add-on board.
MIKROE-6508$23.00
AM/FM 2 Click is a compact add-on board that can be used to listen to music from the AM and FM radio bands. This board features the Si4732, a broadcast AM/FM/SE/LW/RDS radio receiver from Skyworks. This radio receiver integrates the complete broadcast tuner and receiver function from antenna input to digital audio output. In addition to the radio receiver, this Click board™ is equipped with the LM4910, a Boomer output capacitor-less stereo 35mW headphone amplifier from Texas Instruments. This amplifier can deliver 35mW of continuous average power to a 32Ω load with less than 1% distortion. This Click board™ makes the perfect solution for the development of table and portable radios, mini/micro systems, stereo boom boxes, and more.
AM/FM 2 Click is fully compatible with the mikroBUS™ socket and can be used on any host system supporting the mikroBUS™ standard. It comes with the mikroSDK open-source libraries, offering unparalleled flexibility for evaluation and customization. What sets this Click board™ apart is the groundbreaking ClickID feature, enabling your host system to seamlessly and automatically detect and identify this add-on board.
MIKROE-5793$29.00
ATA6570 click is a CAN Partial Networking interface board. The click carries the ATA6570, a high-speed CAN transceiver that interfaces a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus. This IC has some unique features that make it a perfect choice for any embedded CAN application.
It supports both CAN and CAN FD protocol types, partial networking, local and remote wake up, an SPI interface for internal registers configuration, and it features six operating modes as well as the undervoltage and overtemperature protection. The power consumption is taken to a minimum, as the ATA6570 can power down the entire system until a valid wake-up frame is received - even on a busy CAN bus. The car battery supply pin and the CAN bus pins are protected from various interferences and voltage instabilities, typically observed in automotive systems. ATA6570 click provides you with a robust and reliable CAN bus interface.
MIKROE-2900$28.00
