UART I2C/SPI 2 Click is a compact add-on board that provides a high-performance dual UART interface for bridging SPI or I2C processor buses to asynchronous serial communication standards such as RS-232, RS-485, or IrDA. It is based on the MAX3109, a dual UART with 128-word receive and transmit FIFOs from Analog Devices, supporting data rates up to 24Mbps....
GPS/4LTE Combo External Antenna (DLGPS/LTE-C3) provides dual-function signal reception for GPS positioning and 4G LTE communication systems in one compact design. It features a GPS antenna operating at 1575.42MHz±1.023MHz with 5dBic RHCP gain, a low-noise amplifier offering 28dB typical gain with a noise figure below 1.5dB, and an LTE antenna supporting...
RAK4630 Click is a compact add-on board that provides dual-mode wireless connectivity by combining long-range LoRaWAN communication and Bluetooth Low Energy (BLE) for low-power IoT applications. It is based on the RAK4630 module from RAKwireless, which integrates the Nordic nRF52840 MCU with Bluetooth 5.0 support and the Semtech SX1262 LoRa transceiver....
PMIC 2 Click is a compact add-on board designed for energy harvesting in low-power applications, enabling the collection and storage of energy from various sources to power electronic devices autonomously. It is based on the NEH7100, an inductorless power management IC from Nexperia. The NEH7100 supports harvesting from a wide range of light sources and...
Glass Indoor Solar Cell Module (1-cell) provides a compact and ready-to-use energy-harvesting solution for powering low-power electronics in indoor environments. Built around the AMG-1401C amorphous silicon solar cell and mounted on a dedicated PCB, the module offers improved handling, solderable connector pads for DS1069-11 connectors, and accessible...
Color 21 Click is a compact add-on board that provides precise multi-spectral light sensing and ambient color measurement for embedded applications requiring accurate light and color analysis. It is based on the TCS3448, a 14-channel multi-purpose spectral light sensor from ams OSRAM. Covering wavelengths from approximately 380nm to 1000nm, the sensor...
RAK11720 Click is a compact add-on board that provides dual wireless connectivity through LoRaWAN and Bluetooth Low Energy, enabling long-range data transmission and short-range communication for modern IoT applications. It is based on the RAK11720 module from RAKwireless, which integrates the Ambiq Apollo3 Blue AMA3B1KK-KBR-B0 SoC with an ARM Cortex-M4F...
Flash 14 Click is a compact add-on board that provides reliable non-volatile data storage for embedded systems. It is based on the MX25L25645G, a 256Mbit Serial NOR Flash memory from MACOM, offering Single, Dual, and Quad SPI as well as QPI operation modes with clock frequencies up to 133MHz. The memory array is organized into uniform 4KB erasable sectors...
M-BUS RF 5 Click is a compact add-on board that provides long-range wireless data communication between smart meters and gateways using the Wireless M-Bus standard. It is based on the Metis-E Wireless M-Bus module (2609051183000) from Würth Elektronik, operating in the 868.3 to 869.525MHz frequency range for stable and interference-resistant transmission....
Water Pump AW provides reliable and energy-efficient water circulation for various indoor and outdoor applications, ensuring continuous water flow with low noise and minimal power consumption. Based on the AW500S 12V DC brushless motor, it delivers a steady flow rate of 600–800 liters per hour with a maximum head of up to 6 meters while consuming only...
CAN-LIN SBC Click is a compact add-on board that provides high-speed communication over both Controller Area Network (CAN) and Local Interconnect Network (LIN) interfaces, ensuring connectivity between automotive and industrial subsystems. It is based on the ATA6586, a System Basis Chip (SBC) from Microchip that integrates a high-speed CAN transceiver...
SPI to I2C Click is a compact add-on board that enables communication between SPI and I2C interfaces, allowing a host microcontroller to control multiple I2C peripherals even without native I2C support. It is based on the SC18IS604, an SPI-to-I2C bridge from NXP, which manages all I2C-bus operations including protocol handling, arbitration, and timing to...
Current 13 Click is a compact add-on board designed for high-speed current measurement in demanding automotive and industrial applications. It is based on the MLX91218 (MLX91218LDC-AFL-500), a high-accuracy IMC-Hall® current sensor IC from Melexis with integrated overcurrent detection (OCD) and AEC-Q100 Grade 0 automotive qualification. This IC features a...
Vibration LRA Motor 60Hz (LRA2024A-1088F) provides precise linear vibration feedback along the Z-axis, ensuring strong, quiet, and consistent tactile sensations. It operates at 60±10Hz with an input range of 0.1-1.2Vrms AC and up to 200mA rms, offering stable performance and low power consumption. With a 20mm diameter and 24mm body length, it delivers...
Charger 31 Click is a compact add-on board designed to provide intelligent charging for single-cell Li-ion or Li-polymer batteries in embedded applications. It is based on the MP2724, a single-cell buck charger with USB Type-C sink mode from Monolithic Power Systems (MPS), which delivers a low-impedance power path to optimize charging efficiency, reduce...
GNSS 28 Click is a compact add-on board that provides precise multi-constellation satellite positioning and reliable navigation performance for embedded applications requiring high accuracy and low power consumption. It is based on the SL871L (SL871LG3240R003000), a multi-constellation GNSS module from Telit Cinterion built around the low-power Mediatek...
EEPROM 14 Click is a compact add-on board that provides reliable non-volatile data storage for various embedded applications requiring secure and long-term memory retention. It is based on the 24LC512, a 512Kbit I2C serial EEPROM from Microchip, organized as a single block of 64K x 8-bit memory. Built on low-power CMOS technology, the 24LC512 ensures...
Push Button Click is a compact add-on board that provides reliable ON/OFF control and battery freshness management through a pushbutton interface, designed for low-power embedded applications. It is based on the MAX16169, a nanoPower pushbutton ON/OFF controller from Analog Devices with an integrated debounce circuit, latch, and interrupt functionality....
Loading
Load more
Loading
