Filter Product By
Slide and select filter/s
Filtered by
I2C Isolator 2 click provides I2C lines and power isolation for slave devices. It carries the ADM3260 dual I2C isolator with an integrated DC-to-DC converter. I2C Isolator 2 click is designed to run on either 3.3V or 5V power supply. The click communicates with the target microcontroller over an I2C interface with additional functionality provided by the...
Tact Switch 4.5x4.5mm SMD (10pcs)
Buzz 3 Click is a compact add-on board that contains a sounder driver that produces higher volume with a lower current. This board features the PAM8904, a piezo-sounder driver with an integrated Multi-Mode charge pump boost converter from Diodes Incorporated. With its wide input signal range of 20Hz to 300kHz, the PAM8904 can drive a sounder load of up to...
DIGI POT 7 Click is a compact add-on board used as a digitally controlled potentiometer. This board features the AD5175, a single-channel 1024-position digital rheostat with less than ±1% end-to-end resistor tolerance error and 50-time programmable wiper memory from Analog Devices. This I2C configurable IC is designed to operate as a variable resistor for...
Mosaic Click is a compact add-on board for precision navigation and location-based applications. This board features the Mosaic-X5, a compact global navigation satellite system (GNSS) receiver from Septentrio. The Mosaic-X5 stands out for its multi-band and multi-constellation tracking ability, ensuring robust and comprehensive global coverage. It...
M-BUS RF 4 Click is a mikroBUS™ add-on board with a MIPOT 32001324 RF wireless transceiver. This module operates in the 868 MHz SRD Band. Thanks to its small LCC form factor (15 x 25 mm only) and its low power consumption this module allows the implementation of highly integrated low power (battery operated) solutions for water, gas, heat or electricity...
MIC24045 click carries MIC24045 I2C-programmable, high-efficiency, wide input range, 2A synchronous step-down regulator from Microchip. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over I2C interface with additional functionality provided by the following pins on the mikroBUS™ line: RST,...
Alcohol 2 click is a very accurate ethanol gas (alcohol) sensor Click board™, equipped with the SPEC amperometric gas sensor which electrochemically reacts with the ethanol. It is supported by the LMP91000, a high-precision integrated analog front-end IC (AFE), perfectly suited for use in electrochemical sensing applications. The Click board™ also...
Temp&Hum 7 click is a Click board™ which is perfectly suited for measuring the relative humidity (RH) and temperature. The Click board™ is equipped with the Si7021-A20, an accurate and reliable sensor IC, packed in a miniature 3x3mm DFN package. By using the patented low-K polymeric dielectrics, this sensor is available to achieve measurements with a...
mikroLab for PIC XL is the complete solution for 8-bit PIC development, both low-pin and high-pin count. EasyPIC v7 and EasyPIC PRO v7 support more than 550 PIC MCUs.
Tilt 2 click is a tilt sensor switch, which breaks the circuit when tilted to an angle of 45° or when shaken. It is a single-pole-double-throw type of switch (SPDT), which can be operated with up to 24V. The current through the switch should not exceed 25mA. The Click board™ is equipped with the the RB-441-45, a 45° rolling ball sensor switch, which uses...
for STM32F4 CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 5 for STM32F4 CAPACITIVE is not limited to multimedia-based applications only. USB, Ethernet, WiFi and RF connectivity options, digital motion sensor, battery charging functionality, piezo-buzzer,...
Altitude 5 Click is a compact add-on board allowing high-resolution barometric pressure measurement. This board features the KP236, an analog barometric air pressure sensor based on a capacitive principle from Infineon Technologies. The KP236 is primarily developed for measuring barometric air pressure but can also be used in other application fields. It...
The IrDA board features the MCP2155 IrDA driver used for implementing IrDA standard wireless connectivity. The driver also handles IrDA standard protocol stack + bit encoding/decoding.
ADC 7 Click is an advanced 32-bit analog to digital converter (ADC) which uses the LTC2500CDKD-32, a 32-bit oversampling SAR ADC with a configurable digital filter. The filter provides several presets (selectable via the hardware pin), as well as programming of the filtering parameters, via the industry-standard SPI interface. The LTC2500CDKD-32 has some...
BT Audio 3 Click is a compact add-on board with high-performing voice and audio post-processing capability for Bluetooth audio applications. This board features the BM83, a fully certified Bluetooth v5.0 stereo audio module from Microchip. The BM83 contains an onboard Bluetooth stack and audio profiles and supports 24-bit/96 kHz high-resolution audio...
NECTO Studio Monthly subscription is the quickest and easiest way to unlock your NECTO Studio for ALL supported compilers (mikroC AI for ARM, mikroC AI for PIC, mikroC AI for PIC32, mikroC AI for dsPIC, mikroC AI for AVR and GCC toolchain for RISC-V). MIKROE-5228
CAPACITIVE FPI with frame Front Panel Integration Rapid development of multimedia and gui-centric applications
Expand 13 Click is a compact add-on board that contains a multi-port I/O expander. This board features the PI4IOE5V96248, a 48-bit general-purpose I/O expander providing remote I/O expansion for most MCU’s families from Diodes Incorporated. The PI4IOE5V96248 comes in a 6-channel configuration and allows easy addition of I/O through a standard I2C serial...
PWR Meter 3 Click - 90A is a compact add-on board that measures voltage and current through the connected load. This board features the ACS37800KMACLU-090B3-I2C, an I2C-configurable power monitoring solution from Allegro Microsystems, which simplifies the addition of power monitoring to many AC/DC powered systems. The ACS37800KMACLU-090B3-I2C’s...
Boost Click is a compact add-on board that steps up the voltage from its input (supply) to its output (load). This board features the MIC2606, a wide input range boost regulator with an integrated switch and Schottky diode from Microchip. It is a 2MHz PWM DC/DC boost switching regulator that provides an adjustable output voltage. The MIC2606 uses input...
IR Sense 3 Click is the infrared sensor Click board™, designed to be used for the short range IR sensing applications. Unlike other pyroelectric sensors, it is able to sense environmental heat changes up to 1m, even through the glass. IR Sense 3 click has human approach detection algoritam that makes perfectly suited for many human presence detection...
IR Grid click is a thermal imaging sensor. It has an array of 64 very sensitive factory calibrated IR elements (pixels), arranged in 4 rows of 16 pixels, each measuring an object temperature up to 300˚C within its local Field of View (FOV). The MLX90621ESF-BAD IR sensor used on this Click board™ has only four pins, and it is mounted inside of the industry...
Loading
Load more
Loading
