Filter Product By
Slide and select filter/s
Filtered by
4-20mA R Click is a compact add-on board that serves as a receiver in a 4-20mA current loop standard. This board features INA196, a current shunt monitor from Texas Instruments. The INA196 can sense drops across the shunt at common-mode voltages from -16V up to +80V, independent of its supply voltage. Thanks to the boost converter, high input voltages...
Development board for STM32 ARM® Cortex™-M3 and Cortex™-M4, M7, M0 devices. It contains many on-board modules necessary for the application development, including multimedia, Ethernet, USB, CAN and other. Buy now Note: Click boards are not included in the package. STM32 ARM® just found a new home Four connectors for each port Amazing...
Flat Cable 1 allows you to easily connect your prototype board via IDC10 connectors.
Combine click boards™ with ease mikroBUS Shuttle is a small add-on board, which is intended to be used with Shuttle click, in order to expand the mikroBUS™ with additional stacking options. This small add-on board has one mikroBUS™ equipped on itself and it is connected to the Shuttle click via the flat ribbon cable (20cm). One Shuttle click can support...
ETH WIZ Click is a compact add-on that contains an Ethernet controller with a hardwired TCP/IP internet protocol offload engine. This board features the W5500, a fully featured 10/100 Ethernet controller from WIZnet that provides performance, flexibility, ease of integration, and system cost control. It complies with the IEEE802.3 (Full/Half-Duplex...
7seg Click is a compact add-on board representing an easy solution for adding numeric or hexadecimal displays to your application. This board features a double pack of the SN74HC595D, an 8-bit serial-in, parallel-out shift register modules from Texas Instruments, as well as two seven-segment red displays, the JS1-5213AE from Ningbo Junsheng Electronics....
The mikroBUS Cape is an extension for Beaglebone Black, the popular low-cost development platform running Linux. This simple cape has four mikroBUS sockets that allow you to connect more than 1645 different types of Click boards™.
ASLK PRO has been designed for undergraduate engineering students to perform analog lab experiments and provides a cost efficient platform for students to realize almost any analog system using general purpose ICs such as OP-Amps and analog multipliers.
DAC Click is a compact add-on board with a fully-featured, highly accurate digital-to-analog converter. This board features the MCP4921, a 12-bit DAC with an SPI interface from Microchip. The MCP4921 has a rail-to-rail output, low power consumption, and fast setting time over a single channel. The DAC Click also has the MCP1541, a 4.096V voltage reference...
This right angle rubber antena is excelent fit for all GSM click boards that we have in our offer. It has wide bandwith that supports GSM/GPRS modules. Antena has 2m cable with SMA male connector on the end, which alowes you easy positioning in space.
Pi 3 Click Shield is the perfect solution for quickly and easily expanding the capabilities of the Raspberry Pi 3 host board with many Click boards™, enabling the creation of complex and unique projects. It is compatible with Raspberry Pi 3 Model B, 2 B, 1 A+, and B+. Pi 3 Click Shield provides two mikroBUS™ sockets to add any functionality from our...
Wire Jumpers Female to Female (30 cm length, 10pcs - different color)
SpeakUp Click is a compact add-on board providing an offline speech recognition solution. This board features the VS1053, an Ogg Vorbis/MP3/AAC/WMA/FLAC/MIDI audio codec from VLSI Solution. It provides an audio encoder and decoder for those formats on a single chip alongside a low-power DSP processor, data memory, 16KB instruction RAM, and 0.5KB RAM for...
RS232 Click is a compact add-on board representing a universal usable RS232 transceiver. This board features the MAX3232IDRG4, a low-power, true RS-232 transceiver from Texas Instruments. It provides an interface between the TTL/CMOS logic levels commonly used on microcontrollers and the RS-232 bus. RS-232 is a rather old communication protocol that has...
Heart Rate click is a heart rate monitoring and pulse oximetry measuring Click board™. It features an advanced oximeter and heart rate monitoring sensor, which relies on two integrated LEDs, a photosensitive element, and a very accurate and advanced low noise analog front end, to provide clean and accurate readings. It is enough to place an index finger...
Smart programmable touch 2.8'' display, packed with features. Mikromedia can be used for controlling a wide range of applications: from simple hobby projects, up to entire machine installations. It is powered by PIC18F87J50 microcontroller unit, it gives you true power to build GUI-centric embedded applications.
Bluetooth Click is a compact add-on board that provides Bluetooth connectivity for any embedded application. This board features the RN-41, a Class 1 Bluetooth module from Microchip. It is a fully qualified Bluetooth version 2.1 module and supports version 2.1 + Enhanced Data Rate (EDR). With an onboard chip antenna and working on 2402 – 2480MHz...
50-100mil Adapter allows you to connect a mikroProg for STM32 programmer and hardware debugger to a Cortex debug connector.
USB SPI Click is a compact add-on board with a general-purpose USB to an SPI protocol converter. This board features the MCP2210, a USB-to-SPI Master converter that enables USB connectivity in applications with an SPI interface from Microchip. The MCP2210 has a full-speed USB 2.0 compliant controller supporting all four SPI modes with bit rates up to...
LED Driver 5 click is a Click board™ capable of driving an array of high-power LEDs with constant current, up to 1.5A. This Click board™ features the TPS54200, a highly integrated LED driver IC, with many useful features. It consists of a synchronous, fixed-frequency buck converter which operates at 600kHz, providing an excellent size/efficiency ratio....
Accel Click is a compact add-on board that contains an acceleration sensor. This board features the ADXL345, an ultra-low power, 3-axis accelerometer with high resolution (13-bit) measurements from Analog Devices. It allows selectable full-scale acceleration measurements in ranges of ±2g, ±4g, ±8g, or ±16g in three axes with a configurable host interface...
ADC Click is a compact add-on board that converts an analog voltage into a digital representation. This board features the MCP3204, a 4-channel 12-bit A/D converter with SPI serial interface from Microchip. The MCP3204 is specified for a maximum conversion of up to 100ksps as a throughput rate. Its SAR architecture is based on a successive approximation...
MAX232 Boards are used to connect the MAX232 circuit to a prototype board.
Connect shield is an extension board pin-compatible with all mikromedia boards, which allows you to easily establish connections between your board and the surrounding electronics. On-board screw terminals allow you to connect each pin quickly.
Loading
Load more
Loading
