Filter Product By
Slide and select filter/s
Filtered by
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
I2C MUX 3 Click is a compact add-on board that contains eight bidirectional translating switches dedicated for applications with I2C slave address conflicts. This board features the TCA9548APWR, a low voltage 8-channel I2C bus switch with an active-low reset input from Texas Instruments. It possesses three programmable address pins that allow up to eight...
Pressure 13 Click is a compact add-on board that contains an integrated pressure sensor for manifold air pressure measurement applications. This board features the KP229E2701, a miniaturized analog manifold air pressure sensor based on a capacitive principle from Infineon. This sensor converts the pressure of 10 kPa to 300 kPa into an analog output...
Rotary Magnetic Holder represents a solution designed for use alongside magnetic rotary position sensors. It comes with a plastic stand measuring 22x16x10 millimeters (L x W x H), as well as an adjustable shaft with a 6mm diameter magnet, allowing fast prototyping and quick measurements during development. NOTE: Rotary Magnetic Holder can be used very...
DC Motor 22 Click is a compact add-on board that contains a brushed DC motor driver. This board features the TMC7300, a low voltage driver for one or two DC motors from Analog Devices. The TMC7300 is rated for an operating voltage range from 2V to 11V and operates up to two DC motors via simple UART control for direction, velocity, and torque. It also has...
GNSS MAX 2 Click is a compact add-on board designed for precise positioning in urban environments. This board features the MAX-F10S, a professional-grade L1/L5 dual-band GNSS receiver from u-blox. This receiver uses dual-band GNSS technology to provide meter-level accuracy, even in challenging urban areas, by mitigating multipath effects. It supports...
Proximity 11 Click is a close-range proximity sensing Click board™, equipped with the RPR-0521RS, a very accurate and power-efficient proximity and ambient Light Sensor with IrLED. It allows an accurate proximity detection for a maximum distance of 100mm. The proprietary LED current driving technique eliminates the need for calibration, simplifying the...
Ultrasonic 5 Click is a compact add-on board that contains circuits for processing the ultrasonic sensor's output. This board features the TUSS4470, a transformer-drive ultrasonic sensor IC with a logarithmic amplifier from Texas Instruments. In addition to the high selectability of the power supply of the IC itself, this board also allows you to choose...
A smart display solution, mikromedia HMI 7" Cap has a 800x480px color display with a capacitive touch panel on the front, and a powerful FT900Q 32-bit MCU with additional essential circuitry on the back - making it a standalone but cost-effective solution suitable for industrial applications.
Manometer 2 click carries the 5525DSO-SB001GS digital pressure sensor, based on leading MEMS technology from TE Connectivity. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over I2C or SPI interface.
Pressure 5 click is a barometric pressure measurement Click board™, which features the BMP388, an accurate absolute barometric pressure sensor. Due to its very high sensing accuracy, it is perfectly suited for precise altitude tracking applications. The BMP388 pressure sensor can use both SPI and I2C communication protocols, allowing it to be interfaced...
EERAM 3.3V click is a static RAM (SRAM) memory click board™ with the unique feature - it has a backup non-volatile memory array, used to store the data from the SRAM array. Since the SRAM is not able to maintain its content after the power loss, the non-volatile EEPROM backup can be a very handy addition that can be used to preserve the data, even after...
SAML Touch Click is a Click board™ equipped with two capacitive touch pads and one capacitive slider. There are also LED indicators, which are used to indicate touch evens for each of the available touch components: two LEDs (one for each touchpad), and one six-segment bargraph, used to indicate touch position across the slider. SAML click is based on the...
LR 14 Click - 868MHz is a compact add-on board for low-power, long-range wireless communication in IoT networks. This board features the RAK3172, a Class A/B/C LoRaWAN 1.0.3-compliant module from RAKwireless Technology, featuring the STM32WLE5CC ARM Cortex-M4 32-bit chip. This board supports LoRaWAN and LoRa Point-to-Point communication modes and...
Serial Cable with thumbscrews
Stepper 6 click is the complete integrated bipolar step motor driver solution. It comes with the abundance of features that allow silent operation and optimal working conditions for the connected motor. A specialized integrated driver chip on this Click board™ far exceeds the capabilities of similar, commonly used step motor drivers. It comes in the...
BIGPIC6 64-pin TQFP MCU Card Empty PCB
Reduce the GLCD GUI development time considerably with mikroC, mikroBasic or mikroPascal for PIC and SmartGLCD 240x128 development board. Buy this kit and save USD 80$.
ADC 24 Click is a compact add-on board for high-speed analog to digital conversion. This board features the AD7490, a 12-bit, 16-channel successive approximation ADC from Analog Devices, optimized for efficient power usage with a consumption of just 2.5mA from a 5V supply while achieving up to 1MSPS throughput rates. The board features 16 single-ended...
RNG Click is a random number generator (RNG) is a device that generates a sequence of numbers or symbols that cannot be reasonably predicted better than by a random chance. This Click board™ is true hardware random-number generator (HRNG), which generate genuinely random numbers. Random number generators have applications in gambling, statistical...
A high-quality cost-effective 7" TFT display with a resistive touch screen and a metal mounting frame for easier integration. Easy to use with MikroElektronika development tools.
A smart display solution, mikromedia HMI 4.3" UXW has a 480x272px color display with a capacitive touch panel and decorative white bezel on the front, and a powerful FT900Q 32-bit MCU with additional essential circuitry on the back - making it a standalone but cost-effective solution suitable for industrial applications.
A smart display solution, mikromedia HMI 4.3" UXB has a 480x272px color display with a capacitive touch panel and decorative black bezel on the front, and a powerful FT900Q 32-bit MCU with additional essential circuitry on the back - making it a standalone but cost-effective solution suitable for industrial applications.
We wanted to show you how simple is to add wireless control feature to your embedded device using WiFi PLUS click boards. Fancy touchscreen interface implemented on mikromedia for PIC18FJ allows you to view ADC acquisition, digital input and to control digital output on EasyPIC v7 board. WiFi PLUS click board features MCW1001 companion controller with...
Loading
Load more
Loading
