Temp&Hum 20 Click is a compact add-on board that represents temperature and humidity sensing solution. This board features the CC2D23, a highly accurate, fully-calibrated relative humidity and temperature sensor from Amphenol. This sensor, characterized by its high accuracy (±2% from 20% to 80%RH (±3% over entire humidity range)) and high resolution,...
LR 6 Click is a compact add-on board designed for ultra-long-distance spread-spectrum communication. This board features the Ra-01S, a LoRa™ wireless radio frequency module from Ai-Thinker Technology, featuring the SX1268 radio chip. This module provides exceptional sensitivity of over -148dBm, a power output of +22dBm, and supports multiple modulation...
Audio Xover Click is a compact add-on board designed to manage frequency distribution across speakers in audio systems. This board features three precise Butterworth filters and does not rely on a main IC component. The board offers adjustable cutoff frequencies of 120Hz, 90Hz, and 70Hz, ensuring a maximally flat frequency response with sharp roll-off...
Charger 18 Click is a compact add-on board representing a single-cell battery charger. This board features the LTC3553, a micropower, highly integrated power management, and battery charger for single-cell Li-Ion/Polymer battery applications from Analog Devices. Designed specifically for USB applications, it also includes a PowerPath manager with...
Thermostat 4 Click is complete solution that senses the temperature of a physical system and can performs actions so that the system's temperature is maintained near a desired setpoint. It's based on Texas Instruments TMP392, a resistor programmable temperature switch that enable protection and detection of system thermal events from 30°C to 130°C. It...
The 6DOF IMU 11 click is a Click board™ based on the KMX63, a 6 Degrees-of-Freedom inertial sensor system on a single, silicon chip, which is designed to strike a balance between current consumption and noise performance with excellent bias stability over temperature. The KMX63 sensor consists of a tri-axial magnetometer plus a triaxial accelerometer...
nvSRAM Click is a compact add-on board that contains the most reliable nonvolatile memory. This board features the CY14B101J, a 1-Mbit nvSRAM organized as 128K words of 8 bits each with a nonvolatile element in each memory cell from Infineon. The embedded nonvolatile elements incorporate the QuantumTrap technology and provide highly reliable nonvolatile...
Color 18 Click is a compact add-on board for accurate ambient light detection and flicker monitoring. This board features the TCS3530, a true color ambient light sensor from ams OSRAM. The TCS3530 features true color XYZ sensing, flicker detection up to 7kHz, and eight concurrent sensing channels with independent gain configurations. It also includes a...
6DOF IMU 15 Click is a compact add-on board that contains a 6-axis MEMS motion tracking device combining a 3-axis gyroscope and a 3-axis accelerometer. This board features the ASM330LHH, automotive 6-axis MEMS motion tracking device, from STMicroelectronics. It has a configurable host interface that supports both I2C and SPI serial communication, features...
IrThermo Click 3.3V is a compact add-on board that allows contactless measurement of the object's temperature. This board features the MLX90614, a single and dual-zone infrared thermometer from Melexis. It encompasses both the thermopile sensor element and the ASSP, a signal conditioning circuitry that features 17-bit ADC and powerful DSP, which allow a...
Buck-Boost 2 click is an advanced DC-DC step-down/step-up regulator (buck/boost), which is able to provide regulated 5V on its output, regardless of the input voltage. The input voltage can range from 2.7V up to 40V. The Click board™ provides an ultra-low noise and ripple free regulated output, with seamless transitions from buck to boost and boost to...
NFC 2 Click is a compact add-on board that contains a highly integrated NFC transceiver for contactless communication. This board features the PN7150, the best plug&play high-performance full NFC solution with integrated firmware and NCI interface designed for contactless communication at 13.56 MHz from NXP USA Inc. This I2C configurable transceiver...
SolidSwitch Click is a compact add-on board that contains load switch devices. This board features the TPS22918, four single-channel load switches from Texas Instruments. Every switch includes an N-channel MOSFET that operates over an input voltage range up to 5.5V and can support a maximum continuous current of 2 A. The switches are controlled by an...
PSoC® TFT Expansion Board is a breakout board for a 2.8”, 320x240 px MI0283QT-9A TFT display. It's equipped with a microSD slot, and compatible with the CY8CKIT-050 PSoC® 5LP development kit.
MIC23099 click carries the MIC23099, a single AA/AAA cell step-down/step-up regulator with battery monitoring. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over the following pins on the mikroBUS™ line: CS, INT.
Buck 5 Click is a high-efficiency buck (step-down) DC/DC converter, which can provide digitally adjusted step-down voltage on its output while delivering a considerable amount of current. Buck 5 click accepts a wide voltage range on its input - from 5V to 30V. The output voltage may be adjusted via the SPI interface, in the range from 0.9V to...
Hall Current 12 Click is a compact add-on board that provides economical and precise AC or DC current sensing solutions. This board features the TMCS1100A4, a galvanically isolated Hall-effect current sensor capable of DC or AC current measurement with high accuracy, excellent linearity, and temperature stability from Texas Instruments. It enables the...
RN4678 Click is a compact add-on board that provides BT/BLE connectivity for any embedded application. This board features the RN4678, a Bluetooth 4.2 dual-mode module from Microchip. Data transfer is achieved through Bluetooth by sending or receiving data through SPP in Bluetooth (BT) Classic mode and Transparent UART in BLE mode. Over the onboard...
EnOcean 4 Click carries a ultra-low power TCM515U transceiver gateway module which operates at 902MHz radio band, perfectly suited for the realization of transceiver gateways, actuators and controllers for systems communicating based on the EnOcean radio standard. For communication to other devices we have implemented PCB antenna on the board making this...
UVC Light Click is Click board™ with ultraviolet LEDs with 275nm wavelength which can be complemented with UVC Click for measuring exact dose of UV radiation. UVC radiation refers to wavelengths shorter than 280 nm. Because of the spectral sensitivity of DNA, only the UVC region demonstrates significant germicidal properties. As evident by multiple...
This add-on board features the PCM5122 DAC with excellent dynamic performance for audiophile-worthy reproduction of your favorite music, on a budget.
MPU IMU Click is a compact add-on board that can detect movement and acceleration. This board features the MPU-6000, an integrated 6-axis motion device from TDK InvenSense that combines a 3-axis gyroscope and accelerometer alongside a DMP (digital motion processor). The Digital Motion Processor engine is capable of processing complex 9-axis MotionFusion...
Matrix R Click is a compact add-on board that controls two onboard red 5x7 matrices. This board features two MAX7219, serially interfaced, 8-digit LED display drivers from Analog Devices. The active area of each matrix is 7.62mm high and 5.08mm wide. The 7x5 is a standard resolution for displaying ASCII characters, so the Matrix R Click is essentially a...
16x9 click is an array of 144 LEDs, driven by a single IC with relatively low pin count (28). Driving so many LED elements with reasonably low pin count IC is possible by utilizing a cross-plexing LED driving technique. This technique is also known as the Charlie-plexing since it was first proposed by Charlie Allen, an engineer from Maxim Integrated. The...
Loading
Load more
Loading
