Filter Product By
Slide and select filter/s
Filtered by
Categories
Mikroe has collaborated closely with Microchip to offer you a broad portfolio of products from this vendor, which will help you reducing development effort and accelerate time to market. As a 3rd party tool provider we strive to promote partners newest theologies and products, by offering them to the broad market.
Fan 5 Click is a compact add-on board specially designed for fan speed management. This board features Microchip’s TC654, a PWM mode fan speed controller with FanSense™ technology suitable for brushless DC fans. This I2C-configurable controller implements temperature-proportional fan speed control, which reduces acoustic fan noise and increases fan life....
The Fan 6 click is a Click board™ which features EMC2103, an SMBus compliant fan controller with up to up to 3 external and 1 internal temperature channels. The fan driver can be operated using two methods each with two modes. The methods include an RPM based Fan Speed Control Algorithm and a direct PWM drive setting. The modes include manually...
Fan Click is a compact add-on board specially designed for fan speed management. This board features EMS2301, a single/multiple RPM-based PWM fan controller from Microchip. The EMS2301 controls the speed of one four-wire fan operating on 5V, commonly used as coolers in computers and other electronics. The controller supports PWM speeds from 9.5KHz to...
Flash 2 click features a 64 Mbit Flash memory IC, manufactured by using the proprietary high-performance CMOS Super-Flash® technology, which allows the Flash 2 click to withstand up to 100,000 write cycles, with the data retention period of 100 years, which is considerably longer than any other memory module of this type. The flash memory IC used on this...
Flip&Click PIC32MZ is a two-sided development board with a split personality. It can be used with chipKIT core (Arduino-style development environment), but it can also be used with mikroC, mikroBasic, and mikroPascal for PIC32. It’s a beginner-friendly rapid prototyping tool expandable with up to four Click boards.
Flip&Click SAM3X is Arduino's close cousin. It shares a lot of Arduino DNA - the 32-bit MCU, the pinout, the compatibility with Arduino IDE – but when you flip it over, you get four mikroBUS™ sockets for 1645 Click boards™.
Fusion for PIC v8 is a development board for PIC architecture devices. It contains many on-board modules necessary for device development, including multimedia, Ethernet, USB, and others.
Fusion for PIC v8 is packed in the protective box along with the relevant documentation.This box is very resistant to all kinds of damage and shock. The package contains: Damage resistant protective box Fusion for PIC v8 board MCU and Display board flyers Adapter - USB-C Female to USB-A Male Adapter - USB Micro Female to USB-C Male USB-C...
Fusion for PIC32 v8 is packed in the protective box along with the relevant documentation.This box is very resistant to all kinds of damage and shock. The package contains: Damage resistant protective box Fusion for PIC32 v8 board MCU and Display board flyers Adapter - USB-C Female to USB-A Male Adapter - USB Micro Female to USB-C Male...
GainAMP 2 click is a 6-channel programmable gain amplifier, used to amplify signals on any of the 6 non-inverting input channels up to 32x, in eight discrete steps. The gain can be set via the SPI communication interface. The click has a high signal to noise ratio, a good bandwidth, and very low gain error. These features make it an ideal solution for...
Start designing your application with graphical user interface quickly with VisualGLCD and SmartGLCD 240x128 device. Buy this kit and get 30$ USD discount.
Reduce the GLCD GUI development time considerably with mikroC, mikroBasic or mikroPascal for PIC and SmartGLCD 240x128 development board. Buy this kit and save USD 80$.
GSR click can be used to measure the electrodermal activity (EDA) of the human body, also known as the galvanic skin response (GSR). EDA is actually the property of the human body that causes continuous variation in the electrical characteristics of the skin. EDA monitoring is usually combined with the monitoring of the heart rate, respiratory rate, and...
The Heart Rate 9 click is a Click board™ which features PIC16F1779 8-bit MCU and SFH 7060 heart rate and pulse oximetry monitoring sensor. This click has an algorithm for processing data from the sensor and it can send data for 3 different diodes (green, ir, red) who give out a diagram of the heartbeat and its frequency per minute. The data has shown that...
Hydro Probe Click is a capacitive soil moisture sensor based on capacitive changes that are used to detect the volumetric water content in the soil. Water detection is achieved by using function oscillator MIC1557 and ADC converter MCP3221 from Microchip, which allow you to convert moisture presents to the digital value. Compared to resistant soil...
HZ to V click is a device that can converts input frequency of the signal with virtually any wave shape to a DC voltage output, with a level proportional to the input frequency. It has a linear response, and by applying a signal with the frequency between 1kHz to 10kHz on its input, the Click board™ will generate a DC voltage, ranging from 0.33V to 3.3V....
IrDA 3 click is an intelligent IR transceiver device that can both send and receive UART commands via the IR interface. IrDA 3 click features both the IR transceiver and the encoder/decoder IC, used to convert the UART data and send or receive it in IrDA® compatible format. IrDA 3 click also has an onboard clock generator for the fastest possible UART...
IrDA 2 Click is a compact add-on board providing a cost-effective solution for sending and receiving IR serial data. This board features the MCP2120, a Microchip’s high-performance fully-static infrared encoder/decoder for the infrared transceiver module, the TFDU4101 from Vishay semiconductor. The MCP2120 encodes an asynchronous serial data stream,...
LCD Mini Click is a compact add-on adapter board that allows you to interface an LMB162XFW LCD display to any microcontroller. This board features the MCP23S17, a 16-bit I/O expander with a serial interface from Microchip. It allows you to display 2x16 monochrome characters on an LMB162XFW LCD display and is ideal for displaying short messages or numbers...
LED driver 2 click carries the MCP1643 - LED constant current regulator, made by Microchip. It is a compact, high-efficiency, fixed frequency, synchronous step-up converter, optimized to drive one LED with the constant current. It can be powered by a two-cell alkaline/NiMH/NiCd battery (2.4V), or via the mikroBUS™ power supply pins. LED Driver 2 click...
LED driver click carries the MCP1662 high-voltage step-up voltage driver from Microchip. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over PWM pin on the mikroBUS™ line.
LED Flash 2 click is a powerful flash/torch click, featuring the MIC2870 from Microchip, a high-efficiency flash LED driver, optimized for driving one or two high-brightness camera flash LEDs. The MIC2870 IC can drive one high brightness LED up to 1.5A or two high brightness LEDs, up to 750mA each. Two high brightness LEDs are already mounted on the Led...
LR 2 Click is a compact add-on board that contains a low-power, long-range transceiver. This board features the RN2903, RF technology-based SRD transceiver, which operates at a frequency of 915MHz from Microchip Technology. This Click board™ features an embedded LoRaWAN Class A compliant stack, providing a long-range spread spectrum communication with...
LR Click is a compact add-on board that contains a low-power, long-range transceiver. This board features the RN2483, RF technology-based SRD transceiver, which operates at a frequency of 433/868MHz from Microchip Technology. This Click board™ features an embedded LoRaWAN Class A compliant stack, providing a long-range spread spectrum communication with...
Loading
Load more
Loading
