Filter Product By
Slide and select filter/s
Filtered by
Categories
Mikroe has collaborated closely with Microchip to offer you a broad portfolio of products from this vendor, which will help you reducing development effort and accelerate time to market. As a 3rd party tool provider we strive to promote partners newest theologies and products, by offering them to the broad market.
SQI FLASH click is based on the SST26VF064B, a 64 Mbit Serial Quad I/O flash device from Microchip. The chip utilizes 4-bit multiplexed I/O serial interface to boost the performance. The click is a very fast solid-state, non-volatile data storage medium, that can be electrically erased and reprogrammed. Operating at 104 MHz, the SST26VF064B enables...
SRAM Click is a compact add-on board that contains highly reliable nonvolatile memory. This board features Microchip’s 23LC1024, a 1Mbit serial SRAM with each memory cell organized as 128k words of 8 bits each. The serial SRAM provides fast access, infinite read and writes cycles to the memory array, and three operating modes for reading and writing data....
StartUSB for AVR Board is a small development board featuring Atmel AT90USB162 device with fast USB 2.0 support. It features connection pads for all MCU pins, as well as two prototyping areas for placing additional components.
StartUSB for PIC Board is a small development board featuring Microchip® PIC18F2550 device with fast USB 2.0 support. It features connection pads for all MCU pins, as well as two prototyping areas for placing additional devices.
Step Up Click is a fixed frequency DC-DC step-up (boost) regulator, which can be obtained from any low voltage input - such as NiCd, NiMH or one cell Li-Po/Li-Ion batteries. This click features very high efficiency, low noise and anti-ringing voltage output and inrush current limiting with the internal soft-start, as well as true disconnect option for...
Stepper 7 click is a bipolar step motor driver. It features an H-bridge bipolar step motor driver, which supports full and half step control modes. Stepper 7 click also carries a port expander so that the communication can be done with a minimal number of pins, through the mikroBUS™ SPI bus. Stepper 7 click offers thermal protection, integrated kickback...
SWI EEPROM Click is a compact add-on board that provides a highly reliable memory solution. This board features the AT21CS01, a single-wire serial EEPROM with a unique, factory-programmed 64-bit serial number from Microchip Technology. The AT21CS01 has an ultra-high write endurance capability allowing more than one million cycles for each memory location...
Temp-Log 3 click is a temperature measuring Click board™ featuring the MCP9843 IC, an accurate temperature sensor IC with integrated EEPROM. Besides the thermal sensor, this IC is equipped with additional 256 bytes of EEPROM. This can be a very useful option for some applications: it allows any data to be stored within the same IC, so no additional EEPROM...
Temp-Log click is a precise ambient temperature measurement device, equipped with 8Kbit (1024 bytes) of EEPROM memory, which can be used to permanently store system configuration or log application specific or user preference data. This click covers a range of temperatures from -55°C to +125°C with the highest accuracy of ±0.5°C, in the range of 0°C to...
Thermo 5 Click is a compact add-on board that accurately measures temperature. This board features the EMC1414, a multiple-channel temperature sensor with beta compensation from Microchip. The EMC1414 measures temperature in the default range of 0°C to 127°C and extended range of -64°C to 191°C with ±1°C accuracy. Thermo 5 Click can monitor four...
Thermo 7 click is a Click board™ equipped with the sensor IC, which can digitize temperature measurements between -55°C and +125°C so that the temperature measurement data can be processed by the host MCU. Thermo 7 click provides an accuracy of ±1°C in the range from -10°C to +85°C. The sensor used on this Click board™ has a great combination of features...
Thermo 8 click is a very accurate thermometer Click board™, with a very high typical measurement accuracy of ±0.25°C, and great data repeatability, with drift in the range of ±0.0625°C. Besides measuring the temperature, this Click board™ offers a set of very useful features, such as the thermostat function, interrupt event and critical temperature alert...
Thermo J Click is a temperature measurement click board™, which uses a thermocouple type-J probe, connected to a PPC-SMP-J onboard connector. The active part of the Thermo J click is MCP9600 by Microchip - a thermocouple EMF to temperature converter, with 1.5°C of maximum accuracy. The onboard PCC-SMP-J connector ensures the secure connection and accurate...
Thermo K Click is a compact add-on board that serves as a thermocouple type-K probe interface for temperature measurement. This board features the MCP9600, a thermocouple EMF to temperature converter from Microchip. With the versatile type-K probe, this board enables precise temperature measurements of up to +480 °C. However, the capabilities don't stop...
Thermostat 5 Click is a compact add-on board designed for precise temperature monitoring and control of external devices. This board features the MCP6022 operational amplifier and MCP3221 A/D converter, both from Microchip, ensuring accurate signal processing. The board features an NTC connector for temperature sensing, a dual-mode signal processing...
Thermostat 6 Click is a compact add-on board designed for precise temperature monitoring and automated control of external devices. This board features the MCP6022 rail-to-rail operational amplifier and the AZ9403-1C-5DE SPDT relay, ensuring reliable temperature processing and powerful device control. It also features a connector for integrating an NTC...
Thumbstick Click is a compact add-on board that can fulfill your directional analog input needs. This board features COM-09032, a high-quality 2-axis analog output thumbstick from Sparkfun. This small joystick is a 'self-centering' analog type with a black rocker cap similar to the ones used on joypads on popular gaming consoles. It comprises two 10kΩ...
Thunder EMU Click is a compact add-on board that can be used to emulate lightning. This board features circuits that generate an RF signal that mimics lightning strikes. It is a thunder emulator board that allows you to mimic lightning signals that can represent different distances, thus enabling you to debug your lightning detector application for all...
Touch Key 4 click is a capacitive touch sensing Click board™, with the advanced touch/proximity sensor IC. It has three independently configurable channels and can work in several operating modes, including multiple button pattern detection mode, combo mode, press and hold detection mode, power button mode, and more. Capacitive touch sensor inputs are...
TouchKey 2 Click is a compact add-on board with four capacitive pads explicitly designed for touchpad controls. This board features the ATtiny817, an 8-bit AVR microcontroller from Microchip. The ATtiny MCU has an integrated touch QTouch® controller, which supports a capacitive touch interface with proximity sensing. This Peripheral Touch Controller (PTC)...
There are many kinds of touch sensors on the market, but every one of them has some unique features that make it stand out from the crowd. TouchKey 3 click is equipped with seven advanced capacitive sensors, based on the proprietary QTouch® technology. Besides quite a large number of QTouch® capacitive sensor channels, TouchKey 3 click also offers some...
Touchpad 3 Click is a compact add-on board that allows users to easily integrate projected capacitive touch into their applications. This board features the MTCH6301, a turnkey capacitive touch controller that makes it easy for users to use popular multitouch and gesture interfaces from Microchip. This controller’s sophisticated combination of Self and...
Touchpad Click is a compact add-on board that uses the conductive touch of a human finger for input and control. This board features the MTCH6102, a projected capacitive touch controller from Microchip. It utilizes up to 15 channels to support taps, swipes, and scrolling on the X and Y axis on a complete touchscreen sensing solution with a 25x17mm...
Turbidity Click is an adapter Click board™, used to interface a compatible turbidity sensor with the host MCU. This board features one 1x3 2.5mm connector suitable for connecting a Turbidity sensor via an additional 3-wire Male to Male Cable - 15 cm for Turbidity Click specially made for this purpose. It allows users to upgrade their projects with a...
Loading
Load more
Loading
