Filter Product By
Slide and select filter/s
Filtered by
Categories
Mikroe has collaborated closely with ANALOG DEVICES to offer you a broad portfolio of products from this vendor, which will help you reducing development effort and accelerate time to market. As a 3rd party tool provider we strive to promote partners newest theologies and products, by offering them to the broad market.
Proximity 2 Click is a compact add-on board providing a close-range proximity sensing solution. This board features the MAX44000, an I2C-configurable ambient light sensor with an integrated infrared proximity sensor from Analog Devices. The MAX44000 consists of an array of photodiodes that convert light into current, which the internal circuitry converts...
Proximity 6 click is a versatile proximity detection device on a Click board™. It can detect a foreign object distanced up to 20cm. The Click board™ features a detection sensor IC that can trigger a threshold based interrupts, which makes this Click board™ capable of detecting even simple gesture movements. The advanced onboard IC sensor features LED...
PWM 2 click offers 48 independently controlled PWM channels, available over the onboard headers, perfectly suited for driving LEDs. Each channel has a 12-bit PWM register associated to it, with the addition of the 6-bit correction register, also known as the dot correction register. PWM 2 is able to detect both synchronization errors and open LED errors,...
R Meter Click is a compact board with circuitry for measuring the value of resistors. This board features the AD8616, a precision 20MHz CMOS rail-to-rail input/output operational amplifier from Analog Devices. The R Meter can measure a wide range of resistors from 0 up to 1 Mega Ohm. It has three plates for SMD resistors 0603, 0805, and 1206, as well as a...
RF Meter 3 Click is a compact add-on board that collects information, analyzes RF power, and displays information in an easy-to-read digital format. This board features the LT5581, a low-power monolithic precision RMS power detector from Analog Devices. The RMS detector uses a proprietary technique to accurately measure the RF power in a range from 2GHz...
RF Meter Click is a compact add-on board that measures radio frequency power. This board features the AD8318, a logarithmic detector/controller from Analog Devices. It covers a frequency span from 1MHz up to 8GHz over a 60dB range, approximately. The AD8318 acquires the signal over an external antenna, which is then processed by the logarithmic detector...
RMS to DC 2 Click is a compact add-on board that converts the RMS of the input signal into a DC voltage. This board features the AD8436, a low-cost, low-power, true RMS-to-DC converter from Analog Devices. The AD8436 is a translinear precision, low-power, true RMS-to-DC converter that delivers true RMS or average rectified value of AC waveform. It...
RMS to DC click is a Click board™ that is used to convert the RMS of the input signal into a DC voltage, with a value directly readable over the I2C interface. The Click board™ is equipped with the LTC1968, an RMS-to-DC converter IC, which outputs an analog voltage depending on the RMS value of the input signal. The key feature of this IC is its very good...
RS232 Isolator click is a fully isolated dual transceiver click, used to provide secure and easy UART to RS232 conversion, with the galvanic isolation. The digital input and output signals are transmitted across the isolation barrier by utilizing the Analog Devices proprietary iCoupler® technology - IC scale transformer windings couple the digital signals...
RS232 SPI Click is based around the MAX3100, a universal universal asynchronous receiver transmitter (UART) - the first UART specifically optimized for small microcontroller-based systems, from Maxim Integrated. Because of the features contained in its modules, the RS232 SPI Click can be used for handheld instruments, small networks in HVAC or Building...
RS485 2 click is an RS422/485 transceiver Click board™, which can be used as an interface between the TTL level UART and the RS422/485 communication bus. It features a half-duplex communication capability, true failsafe receiver input, driver output protection, low power consumption, 3.3V and 5V compatibility, and more. It is well suited for transmitting...
RS485 4 Click offers an UART to RS485 signal conversion, featuring the ADM2795E specialized IC with the complete galvanic isolation. Digital input and output signals are transmitted across the isolation barrier by using the ICoupler®, an IC scale transformer technology, which allows signals to be magnetically coupled across the isolation barrier within...
The RS485 5 Click is a Click board™ equipped with the MAX485, low-power, slew-rate-limited transceiver for RS-485 and RS-422 communication, from Analog Devices. This device supports half-duplex RS-485 communication and can be used as an interface between the TTL level UART and the RS485 communication bus. Thanks to the low power consumption and reduced...
RS485 Click 5V is a compact add-on board that can be used as an interface between the TTL level UART and the RS422/485 communication bus. This board features the ADM485, a low-power EIA RS-485 transceiver from Analog Devices. It features a half-duplex communication capability, bus Idle, open and short-circuit detection, thermal shutdown, and more. It is...
RS485 Isolator 2 Click features ADM2867E a 5.7 kV rms signal and power isolated full duplex RS-485 transceiver. The device also features cable invert pins, allowing the user to quickly correct reversed cable connection on A, B, Y, and Z bus pins while maintaining receiver full receiver fail-safe performance. This full duplex device allows for independent...
RS485 Isolator 3 Click is a compact add-on board that provides electrical isolation and signal conditioning for RS485 communication systems. This board features the ADM2763E, a 500kbps, 5.7kV RMS, signal-isolated RS-485 transceiver from Analog Devices. The ADM2763E is protected against ≥±12 kV contact and ≥±15 kV air IEC 61000-4-2 electrostatic discharge...
RS485 Isolator Click is a compact add-on board that provides electrical isolation and signal conditioning for RS485 communication systems. This board features the ADM2682E, a signal, and a power-isolated RS-485 transceiver with ESD protection from Analog Devices. It is a 5KVrms isolated RS485/RS422 transceiver with ±15kV ESD protection that can be...
RTC 10 Click is a real-time clock module which has an extremely low power consumption, allowing it to be used with a single button cell battery, for an extended period of time. It features the DS3231M, a low-cost, extremely accurate, I2C real-time clock (RTC) from Analog Devices. The device incorporates a battery input and maintains accurate timekeeping...
RTC 12 Click is a compact add-on board that measures the passage of time. This board features the DS1343, a low-current SPI-configurable real-time clock (RTC) from Analog Devices. This timekeeping device provides an extremely low standby current permitting longer life from a backup supply source. Its clock/calendar feature provides seconds, minutes,...
RTC 19 Click is a compact add-on board that measures the passage of real-time. This board features the MAX31334, an I2C-configurable real-time clock with an integrated power switch from Analog Devices. The MAX31334 provides information like seconds, minutes, hours, days, months, years, and dates based on a 32.768kHz quartz crystal through an I2C serial...
RTC 2 Click is a compact add-on board that keeps track of time in various applications. This board features the DS1307, a 64x8 serial I2C Real-Time clock from Analog Devices. The RTC 6 Click tracks hours, minutes, seconds, days, months, years, and weekdays, with leap year compensation until 2100. The clock frequency is derived from an onboard 32.768KHz...
RTC 4 Click is a compact add-on board that accurately keeps the time of the day. This board features the DS2417, a real-time clock/calendar with a 1-Wire MicroLAN interface and a programmable interrupt for system output from Analog Devices. The DS2417 has a factory-lasered 64-bit registration number, enabling multiple RTC 4 Click boards™ to be connected...
RTC 7 Click is a real time clock module which has an extremely low power consumption, allowing it to be used with a single button cell battery or a super capacitor, for an extended period of time. The MAX31341B IC built on the RTC 7 click is able to output the time in the binary coded decimal (BCD) format. Integrated, factory calibrated XTAL operating at...
RTD click is based on MAX31865 resistance to digital converter from Analog Devices, optimized for platinum resistance temperature detectors, or RTD. The click uses the PT100 type platinum probe for temperature measurement. There are four screw terminals on the board, so different PT100 probe types can be used with this design. This click board™ can work...
Loading
Load more
Loading
