Anyone has the mikroBasic example for the RFID board sold by mE?
There is no example in the mE website for the board.
Hansolo
RFID Board Example
Hi,
Examples for RFid Reader Board are in the final test phase.
They will be available on our web site very soon.
If there aren't any unforeseen problems you should be able
to download examples for RFid Reader Board from our web site
http://www.mikroe.com/en/tools/rfid/
early next week.
Thank you for your patience.
Examples for RFid Reader Board are in the final test phase.
They will be available on our web site very soon.
If there aren't any unforeseen problems you should be able
to download examples for RFid Reader Board from our web site
http://www.mikroe.com/en/tools/rfid/
early next week.
Thank you for your patience.
LibStock
http://www.libstock.com/
mikroSDK
https://www.mikroe.com/mikrosdk
mikroBUS
https://www.mikroe.com/mikrobus
http://www.libstock.com/
mikroSDK
https://www.mikroe.com/mikrosdk
mikroBUS
https://www.mikroe.com/mikrobus
Examples for RFid Reader Board are available for download.
You can download these examples on this address:
RFid Reader Board
You can download these examples on this address:
RFid Reader Board
"Good ideas are not complicated, they are
complex, but we are making it easy !!!"
complex, but we are making it easy !!!"
a question about rfid reader example, is it normal that if no rfid is present (all rfid chips I have are 13MHz, and this is 125KHz reader I got from MikroE so now looking for some 125KHz ones) example constantly fails onmarko wrote:Examples for RFid Reader Board are available for download.
You can download these examples on this address:
Code: Select all
if (!(data[data_index] ^ data[data_index-1]))
{
bad_synch = 1;
break; //bad synchronisation
}
now, I do not have the 125KHz chip to try to read it, but this "bad sync" is kinda strange...
thanks for the info
Re: RFID Board Example
Hello All, any answer to the above question?
I'm facing the same issue with you RFID Reader.
I've noticed that the 8-bit example is working properly but not the 24bit example stored in the dsPic folder.
Any suggestions?
Thank you
Marco
I'm facing the same issue with you RFID Reader.
I've noticed that the 8-bit example is working properly but not the 24bit example stored in the dsPic folder.
Any suggestions?
Thank you
Marco
- Aleksandar.Mitrovic
- mikroElektronika team
- Posts: 1697
- Joined: 11 Mar 2015 12:48
Re: RFID Board Example
Hi Marco,
Which hardware have you use with this RFID Reader board and which microcontroller?
Kind regards,
Aleksandar
Which hardware have you use with this RFID Reader board and which microcontroller?
Kind regards,
Aleksandar
Re: RFID Board Example
Hi Aleksander
I am using the fusion board with mcu card and PIC24FJ128GA310.
I have added a new topic because of different hw here:
http://forum.mikroe.com/viewtopic.php?f=101&t=67756
With the fusion board i noticed that there is no 5v supply selectable..
For this i took the 5v supply from the usb pin and supplied the rfid reader.
Then i ve used the rb0 1 2 and 3 for the interfaces.
About the clock i ve noticed that the pic is going very slow and need to use the pll in order to catch properly the clock interrupt. Any suggestion for the clock/pll sertings? On board i have a 8MHz crystal.
Thank you
I am using the fusion board with mcu card and PIC24FJ128GA310.
I have added a new topic because of different hw here:
http://forum.mikroe.com/viewtopic.php?f=101&t=67756
With the fusion board i noticed that there is no 5v supply selectable..
For this i took the 5v supply from the usb pin and supplied the rfid reader.
Then i ve used the rb0 1 2 and 3 for the interfaces.
About the clock i ve noticed that the pic is going very slow and need to use the pll in order to catch properly the clock interrupt. Any suggestion for the clock/pll sertings? On board i have a 8MHz crystal.
Thank you