Filter Product By
Slide and select filter/s
Filtered by
Trust M Click is trust anchor add-on board for advanced security combined with high performance for connected devices that address individual needs in the field of embedded authentication, brand protection and further security applications. Its based on SLS 32AIA010 OPTIGA™ Trust M1 high-end security controller from Infineon, that features advanced...
Accel 15 Click is a compact add-on board that contains a longevity acceleration sensor. This board features the BMA490L, a high-performance 16-bit digital triaxial acceleration sensor with extended availability of up to ten years from Bosch Sensortec. It allows selectable full-scale acceleration measurements in ranges of ±2g, ±4g, ±8g, and ±16g in three...
Thermostat 2 click is a general-purpose thermostat Click board™ designed to be used with any temperature sensor based on the DS1820 sensor design: 3-pin package with 1-Wire® communication interface. The Click board™ is equipped with a 3-pole terminal and a 3-pin female socket. DS1820 (or compatible) sensor can be connected either over the terminal or can...
CAN Isolator 2 Click is a compact add-on board that provides isolated CAN communication. This board features the ISO1042, an isolated CAN transceiver from Texas Instruments. This galvanically-isolated CAN transceiver meets the ISO11898-2 specifications and offers a +/-70V DC bus fault protection, along with the +/-30V of common mode voltage range. The...
MCU card with PIC18F8520 Microcontroller
LLC-I2C click can be utilized as the level converter for logic signals, which makes it a very useful Click board™. The topology of this logic level conversion (LLC) circuit is perfectly suited for the bi-directional I2C communication. Although there are some specialized integrated circuits on the market, sometimes it is more convenient to have a simple...
DMX Click is a device used to establish communication between the MCU and equipment that uses the DMX512-A communication protocol. Unlike many similar solutions on the market, this unique device allows using the common UART data format, which is converted to an appropriate DMX512 format by the powerful PIC18F26K42 MCU from Microchip. This MCU has an...
DC Male Power Jack TH is a relatively simple component, also known as a barrel connector, responsible for receiving power, and usually mounted on the PCB or chassis of an electronic device. Because of its center pin, this barrel connector represents a male power jack, capable of withstanding current and voltage ratings up to 5A and 24VDC (500VAC at...
The mikroBoard is miniature development tool which includes microcontroller, programer, small proto board and two 2x40 female headers for connection with UNI-DS6 development system.
A high-quality cost-effective 3.5" TFT display with a resistive touch screen and a metal mounting frame for easier integration. Easy to use with MikroElektronika development tools.
Nano Power click is a boost (step-up) DC-DC converter click with extremely high efficiency and very low input voltage, aimed at the low power IoT market and battery-powered sensors and other devices. The input voltage can be very low: the conversion will start for voltages down to 0.95V, providing 5V to the connected load. Once started, the input voltage...
Buggy is a robot rover platform expandable with all sorts of sensors and transceivers. A dream car for hackers and makers. Multiple kits available.
Heart Rate 8 click is an optical biosensor Click board™, designed for heart-rate monitoring (HRM). This Click board™ employs a specialized sensor that incorporates three LED drivers and two photo-sensing elements, sensitive to green and IR light. The green light is most commonly used to measure the dilatation of the blood vessels; therefore, Heart rate 8...
Buck-Boost 2 click is an advanced DC-DC step-down/step-up regulator (buck/boost), which is able to provide regulated 5V on its output, regardless of the input voltage. The input voltage can range from 2.7V up to 40V. The Click board™ provides an ultra-low noise and ripple free regulated output, with seamless transitions from buck to boost and boost to...
The MCU card contains TM4C123GH6PZ microcontroller which is loaded with on-chip modules and is a great choice for both beginners and professionals. After testing and building the final program, this card can also be taken out of the board socket and used in your final device.
V to HZ click is a device that converts an analog voltage input signal into a pulse wave signal of a certain frequency. It has a linear response, so applying a voltage in a range of 0 to 5V on its input, will result in generating the pulse train with frequency linearly proportional to the input voltage. This click features very good linearity, covers a...
AD-SWIO Click is a quad-channel software configurable input/output solution based on AD74412R. The AD74412R is a quad-channel software configurable input/output integrated circuit for building and process control applications. The device provides a fully integrated single chip solution for input and output operation. The AD-SWIO Click contains four 13-bit...
LED Driver 10 Click is a compact add-on board that simplifies the control of multiple LEDs. This board features the TLC59283, a 16-channel, constant-current sink light-emitting diode (LED) driver with pre-charge FET from Texas Instruments. Each LED channel can be individually controlled with a simple SPI serial communication protocol compatible with both...
LEM Click is a compact add-on board that can measure AC and DC currents with exceptional speeds of up to 300KHz. This board features the LTS 6-NP, a current transducer from Lem. Considering the AC and DC currents, it is intended for the electronic measurement of pulsed, mixed with galvanic separation between the primary and the secondary circuits. The...
RTC 20 Click is a compact add-on board that measures the passage of real-time. This board features the AB0805, an I2C-configurable real-time clock with a highly sophisticated feature set from Abracon LLC. The AB0805 provides information like seconds, minutes, hours, days, months, years, and dates based on a 32.768kHz quartz crystal through an I2C serial...
Button Y click is a Click board™ equipped with the tactile switch, sometimes referred to as a pushbutton. A pushbutton is a component that is used very often in various designs, allowing the user to interact with the application. Although it sounds simple, a button needs to comply with a range of application requirements. It needs to have a very good...
Pressure 15 Click is a compact add-on board that contains a board-mount pressure sensor. This board features the LPS27HHW, an ultra-compact piezoresistive absolute pressure sensor that functions as a digital output barometer from STMicroelectronics. The device comprises a sensing element and an IC interface that communicates through I2C or SPI serial...
Haptic 3 Click is a compact add-on board that uses advanced vibration patterns and waveforms to convey information to a user. This board features the DA7282, a linear resonant actuator (LRA), and an eccentric rotating mass (ERM) haptic driver from Renesas. The DA7282 features LRA or ERM drive capability with automatic closed-loop LRA resonant frequency...
LED Flash 3 Click is a compact add-on board representing a powerful flash/torch solution. This board features the KTD2691, an inductor-less, single-flash LED driver from Kinetic Technologies. It includes one current source that can drive up to 1.5A of LED flash current or up to 376mA of torch current. No matter the mode used, it allows you to control the...
Loading
Load more
Loading
