Filter Product By
Slide and select filter/s
Filtered by
I2C 1-Wire 2 Click is a compact add-on board bridging I2C master interfaces with 1-Wire slave devices, ideal for simplifying complex communication protocols. This board features the DS2485, an advanced 1-Wire master with memory from Analog Devices. It features adjustable internal timers for precise 1-Wire signal management, relieving the host processor of...
I2C Isolator 3 Click is a compact add-on board that offers completely isolated bidirectional communication. This board features the CPC5902, a dual optically isolated bidirectional logic-bus repeater from IXYS Integrated Circuits Division. The CPC5902 pass DC signals and don’t need to be clocked periodically to sustain the logic states. It supports I2C...
Pollution Click is a compact add-on board that can detect the presence of organic gases. This board features the WSP2110, a VOC gas sensor from Winsen. The sensitive material of the WSP2110 is Al2O3, which reacts with lower conductivity in clean air. When target pollution gas exists, the sensor’s conductivity increases alongside the gas concentration. It...
The Heart Rate 9 click is a Click board™ which features PIC16F1779 8-bit MCU and SFH 7060 heart rate and pulse oximetry monitoring sensor. This click has an algorithm for processing data from the sensor and it can send data for 3 different diodes (green, ir, red) who give out a diagram of the heartbeat and its frequency per minute. The data has shown that...
TFT Board 7 Capacitive with bezel is a 7" display board which features the standardized 2x20-pin display connector. The display board integrates a capacitive multitouch panel with swipe and zoom gesture support. The TFT display module supports up to 24-bit pixel format (RGB: 888), allowing a true-color palette of 16,7 million colors, and resolution of...
The Serial GLCD 240x128 Adapter Board is an effective, low-cost board used to connect your device to a 240x128 GLCD T6963C. The board has an on-board serial port expander MCP23S17 as well as a potentiometer used to adjust GLCD contrast.
RGB Driver click is an RGB LED driver, capable of driving RGB LED stripes, LED fixtures and other RGB LED applications that demand an increased amount of current and voltage. Besides the NCP5623B IC, a triple output RGB LED driver IC which uses I2C interface for the communication with a microcontroller (MCU), this Click board™ is equipped with three...
USB UART 4 click offers a USB to asynchronous serial data (UART) interface, allowing the microcontroller based designs to communicate with the personal computer, in a very simple way. It is equipped with the FT232RL, a very popular USB to UART interface IC, used on many MikroElektronika devices - both for its reliability and simplicity. USB UART click is...
Reduce the TFT GUI development time considerably with mikroC, mikroBasic or mikroPascal for ARM and mikromedia for STM32 M4 board. Buy this kit and save USD 80$.
MMC Ready Board The MMC Ready Board is a complete development solution for MMC/SD based mass storage devices. It is powered by the PIC18F252 device connected to the memory slot, connection pads and external programmer connector. MMC/SD Ready Card Board can easily become your fast data acquisition device. Because it has microcontroller on board, it can...
Ethernet STM32F10x series Empty MCU Card. Card is not populated with components. Pin distance 100mil.
Charger 25 Click is a compact add-on board that contains a battery charger. This board features the BQ25792, a buck-boost battery charger with a dual-input selector, and a USB PD3.0 OTG output from Texas Instruments. It is fully integrated for 1-4 cell Li-Ion and Li-Polymer batteries. Designed specifically for USB applications, it also includes a Narrow...
The E-Ink technology is a reasonably new technology with a promising future, widely commercialized by the E-INK company. The content displayed on the E-INK (also known as E-Paper) display does not degrade when exposed to direct sunlight, the display actually behaves like a real paper; it is more readable when there is more light hitting its surface....
Flash 10 Click is a compact add-on board representing a highly reliable memory solution. This board features the AT25FF321A, an SPI configurable 32Mbit (2Mx16) serial Flash memory solution from Dialog Semiconductor. The AT25FF321A is an ideal solution for systems in which program code is shadowed from Flash memory into embedded or external RAM (code...
H-Bridge 11 Click is a compact add-on board that allows a voltage to be applied across a load in either direction. This board features the MAX22200, an octal serial-controlled solenoid and motor driver from Analog Devices. The MAX22200 is SPI-configurable and rated for an operating voltage range from 4.5V to 36V. Each channel features a low impedance...
Ribbon Cable 16-wire, Male/Female, 20 cm
Opto Encoder 3 Click is a linear incremental optical sensor/encoder click, which can be used for the movement or rotation encoding. The TCUT1800X01 sensor is equipped with one infrared LED with the wavelength of 950nm, and four phototransistors. Encoders of this type are widely used for many applications which involve precise detection of the position,...
Gyro 6 Click is a compact add-on board that contains a high-performance gyroscope. This board features the IAM-20380, a 3-axis, digital-output X-, Y-, and Z-axis angular rate sensor (gyroscope) from TDK InvenSense. It has a full-scale programmable range of ±250DPS, ±500DPS, ±1000DPS, and ±2000DPS with a factory-calibrated initial sensitivity and...
Magneto Click is a compact add-on board containing an accurate and reliable magnetic sensing device. This board features ams AG’s AS5048A, a 360° angle position sensor with a 14-bit high-resolution output. The AS5048A measures the absolute position of the magnet’s rotation angle, consisting of Hall sensors, analog-digital converter, and digital signal...
BLE 6 Click is a Bluetooth low energy system-on-chip application processor certified module, compliant with BT specifications v5.0 and BQE qualified. The featured BlueNRG-M2 module developed by STMicroelectronics supports multiple roles simultaneously and can act at the same time as Bluetooth master and slave device. The BlueNRG-M2 is based on the...
dsPIC-Ready4 Board dsPIC-Ready4 Board is the best solution for fast and simple development of 28-pin dsPIC30F microcontroller applications (dsPIC30F1010, dsPIC30F2020 etc.). It includes connectors for connecting the dsPICprog with mikroICD in-system stand-alone programmer. These connectors enable you to program microcontrollers without any other...
The BIGdsPIC6 is a development system for 64- and 80-pin dsPIC30F devices. Board is delivered with a MCU card that contains dsPIC30F6014A. The system features a USB 2.0 programmer with mikroICD and many peripheral modules such as Piezo speaker, EEPROM, FTDI, RTC, CAN, etc.
8-pin I2C Click is a compact add-on board that represents a breakout board that simplifies the connection of add-on boards with 8 pin Female Connector to mikroBUS™ socket. This board can be used as I2C Adapter with no main component on itself, with only an on-board connector for connection establishing. 8-pin I2C Click has no regional restrictions, no...
This bundle provides a narrow-band power line communication (N-PLC) solution that uses existing electrical power lines to transmit data signals. It allows users to easily combine the N-PLC Click based on the ultimate N-PLC transceiver, the SM2400, from Semitech with N-PLC Wall Adapter (power line communication AC coupling circuit) to deliver a flexible...
Loading
Load more
Loading
