Filter Product By
Slide and select filter/s
Filtered by
UVC Click is an ultraviolet sensing board which complements UVC Light Click for a ultimate ultraviolet solution. The board is based on GUVC-T21GH ultraviolet sensor from GenUV, capable of measuring UVC spectrum in the range of 220nm up to 280nm and light intensity from 0mW/cm² up to 9.3mW/cm². With high sensitivity and good solar blindness, it can be a...
Instead of keeping your wire jumpers jumbled up like a bowl of spaghetti, consider this pack of 140 wire jumpers in a nifty box for easy storage.
The TouchPanel Controller PROTO Board enables you to connect your prototype device to a Touch Panel. There is also a Touch Panel controller with a connector provided on the board.
The RS485 5 Click is a Click board™ equipped with the MAX485, low-power, slew-rate-limited transceiver for RS-485 and RS-422 communication, from Analog Devices. This device supports half-duplex RS-485 communication and can be used as an interface between the TTL level UART and the RS485 communication bus. Thanks to the low power consumption and reduced...
SRAM Click is a compact add-on board that contains highly reliable nonvolatile memory. This board features Microchip’s 23LC1024, a 1Mbit serial SRAM with each memory cell organized as 128k words of 8 bits each. The serial SRAM provides fast access, infinite read and writes cycles to the memory array, and three operating modes for reading and writing data....
The EasyBee3 Board includes the MRF24J40MA module used to connect your development board to wireless 2.4 GHz IEEE 802.15.4 network easily. The module communicates with microcontrollers via a Serial Peripheral Interface (SPI).
Heart Rate 2 Click is an add-on board based on MAXM86161 from Analog Devices a complete, integrated, optical data acquisition system, ideal for optical pulse oximetry and heart-rate detection applications. The optical readout has a low-noise signal conditioning analog front-end (AFE), including 19-bit ADC, an industry-lead ambient light cancellation (ALC)...
SpeakUp 2 Click is a compact add-on board providing an offline speech recognition solution. This board features the FT900Q, a microcontroller from FTDI Chip. The SpeakUp 2 Click can be set to recognize up to 100 voice commands and have the FT900Q carry them out instantly. The FT900Q, which has stored voice commands, compares them with those received from...
The R2R DAC Board features an on-board digital-to-analog converter R2R that uses R/2R-network and rail-to-rail operational amplifier MCP6284 (450 uA, 5 MHz). The board is connected to a prototype device via an on-board IDC10 connector.
Hi-brightness RGB LED matrix panel, with 1024 RGB LEDs arranged in a 32x32 grid on the front on a 5mm grid, total size 160x160mm. Comes with one IDC cable and a power cable.
PIC18F8520 microcontroller. Featuring nanoWatt technology, it has up to 10 MIPS operation, 128K bytes of linear program memory, 3840 bytes of linear data memory, and lot of internal modules.
UV Click is a compact add-on board that alerts users of excessive ultraviolet radiation levels. This board features the ML8511A, an ultraviolet light sensor suitable for acquiring UV intensity indoors or outdoors from Rohm Semiconductor. The ML8511A is equipped with an internal amplifier converting photocurrent to voltage depending on the UV intensity...
The SmartGPS is a development tool that will help you understand GPS technologies. Connect GPS (Global Positioning System) to your PC or development board using the LEA-6S module. The intuitive design of SmartGPS guides you through the process of learning GPS.
Accel 3 Click is a compact add-on board that contains an acceleration sensor. This board features the H3LIS331DL, a low-power, high-g 3-axis digital accelerometer from STMicroelectronics. This MEMS motion sensor features ultra-low power operational modes that allow advanced power saving, smart sleep-to-wakeup functions, and shock detection with a 1000g...
The BIG8051 development system supports 100-pin Silabs 8051 microcontrollers. It comes with the c8051f040 microcontroller. The system is delivered with a Silabs USB 2.0 programmer and many peripheral modules such as Serial Ethernet, DAC, ADC etc.
Click BoosterPack 2 is an extension for Texas Instruments LaunchPads™ with the current BoosterPack Pinout Standard. It has two mikroBUS™ host sockets onboard, for simple and easy integration of 1645 Click boards™ with a LaunchPad™.
The Digital Potentiometer Board includes a SPI Interfaced single-channel digital potentiometer MCP41010. The board enables you to set potentiometer values from 0 to 10 kΩ. It comes with many simple and ready-to-use examples.
Button R Click is a compact add-on board equipped with a tactile switch, sometimes called a push button, making it the simplest solution for adding a single push button to your design. This board features the 3006.2112, a tactile switch with integrated independent red LED from Marquardt. It provides a user interface tactile feel with visual feedback,...
PHT Click is a compact add-on board that contains a PHT combo sensor. This board features the MS8607, a digital combination sensor providing 3 environmental measurements all-in-one: pressure, humidity, and temperature from TE Connectivity. This sensor is based on leading MEMS technologies, provides factory-calibrated PHT data available over an I2C serial...
USB to I2C Click is an adapter add-on board with a general-purpose USB master to I2C/UART serial interface. This board features the FT260 from FTDI, an interface device controller that provides a bridge between standard USB Human Interface Device (HID) class drivers and an I2C or UART slave devices. The FT260Q is highly-integrated with a USB 2.0-compliant...
BLDC Motor with Hall sensor, from the 42BLF motor series, represents the star wiring type Brushless DC Motor with Hall Effect angle of 120°. With a motor length of 47mm and a weight of 0.29kg, this BLDC motor is rated for a voltage value of 24VDC, at a speed of 4000 ± 10% RPM. It performs its Normal mode of operation at a temperature range of -20 to +50...
Fan Click is a compact add-on board specially designed for fan speed management. This board features EMS2301, a single/multiple RPM-based PWM fan controller from Microchip. The EMS2301 controls the speed of one four-wire fan operating on 5V, commonly used as coolers in computers and other electronics. The controller supports PWM speeds from 9.5KHz to...
ADC 4 click is an advanced analog to digital multichannel converter, which can sample inputs from 16 single-ended channels or 8 differential input channel pairs. This device has a quite high sampling resolution of 24 bits and the output data rates can range from 5 SPS to 250 kSPS. Besides the internal 2.5V reference voltage source, ADC 4 click is also...
RTC 7 Click is a real time clock module which has an extremely low power consumption, allowing it to be used with a single button cell battery or a super capacitor, for an extended period of time. The MAX31341B IC built on the RTC 7 click is able to output the time in the binary coded decimal (BCD) format. Integrated, factory calibrated XTAL operating at...
Loading
Load more
Loading
