Filter Product By
Slide and select filter/s
Filtered by
Noise Click is a compact add-on board that allows you to add noise-detecting circuitry to your application. This board features the MCP4921, a 12-bit DAC with an SPI interface from Microchip. The sound this Click board™ receives through an analog microphone. The Noise Click triggers an interrupt when the ambient sound volume reaches the set threshold. The...
Standard solderless breadboard. It has 2 power buses, 30 columns and 10 rows - a total of 400 contact points.
AC Current sensor is a non-invasive sensor for measuring alternating current. This split-core type of sensor can be clipped around either a live or neutral wire.
Signal Relay Click is a compact add-on board with four relays that any host microcontroller can control. This board features four G5V-1, an ultra-miniature, highly sensitive single-pole double-throw (SPDT) relay for signal circuits from Omron. The Signal Relay Click comes equipped with the 8-pin screw terminal, two for each relay. Through them, the relays...
The Easy8051 v6 is compatible with 14-, 16-, 20-, 28-, 40-pin PLCC44 and PLCC32 MCUs. It comes with an AT89S8253. The board has a USB 2.0 programmer and many peripherals such port expander, MENU and 4x4 keypads etc. Note: the COG display is not included in the package; instead the package includes an LCD 2x16 display.
PIC18F87J50 microcontroller. Featuring nanoWatt technology, it has up to 10 MIPS operation, 128K bytes of linear program memory, 3936 bytes of linear data memory, and lot of internal modules.
DAC 2 Click is a compact add-on board with a fully-featured digital-to-analog converter. This board features the LTC2601, a highly accurate 16-bit voltage-output digital-to-analog converter from Analog Devices. The LTC2601 has high rail-to-rail output drives and double-buffered data latches, communicating with the target MCU through the compatible SPI...
RN4678 Click is a compact add-on board that provides BT/BLE connectivity for any embedded application. This board features the RN4678, a Bluetooth 4.2 dual-mode module from Microchip. Data transfer is achieved through Bluetooth by sending or receiving data through SPP in Bluetooth (BT) Classic mode and Transparent UART in BLE mode. Over the onboard...
Extension cable with jack (female) connector, (2.1x5.5x11-S to S/T) 2wc 0.2m. Operating temperature 0-40 °C.
This straight GSM/GPRS Magnetic Antenna is an excellent choice for GSM/GPRS click boards from our offer. The antenna has a magnetic base so it can be attached to any metal surface. It is equipped with 2m of cable, with an SMA connector on its end, allowing it to be connected to the Click board™ or the female SMA module connector. With 2m of cable, it...
HDC1000 Click is a compact add-on board representing a temperature and humidity sensing solution. This board features Texas Instruments’s HDC1000, a digital humidity sensor with an integrated temperature sensor providing excellent measurement accuracy at low power. The HDC1000 is characterized by its high accuracy (±3% RH and ±0.2°C over a wide operating...
Note: This sensor is not recommended for new design. This product is obsolete. BlueTooth 2 Stick Board offers low power, highly economic wireless capability to your products. On-board WT41 offers impressive 1000 meters range between two bluetooth modules. It uses easy and simple UART protocol for communication.
Ribbon Cable 40-wire, Female/Female, 20 cm
Load cell 2 Click is a weight measurement click which utilizes a load cell element, in order to precisely measure the weight of an object. The Load Cell 2 Click can be used with the strain gauge type of load cells with external differential reference voltage range from 0.1V to 5V. The strain gauge load cell is typically a circuit made of four strain...
Ozone 2 click is an Ozone detection (O3) sensor, based on the MQ131 gas sensor. This gas sensor has a sensitive layer made of SnO2, which changes its resistance when exposed to ozone. The sensor is able to sense O3 concentration in the range of 10 ppm to 1000 ppm. The Click board™ is also equipped with a trimmer potentiometer, used to adjust the...
RS485 2 click is an RS422/485 transceiver Click board™, which can be used as an interface between the TTL level UART and the RS422/485 communication bus. It features a half-duplex communication capability, true failsafe receiver input, driver output protection, low power consumption, 3.3V and 5V compatibility, and more. It is well suited for transmitting...
6DOF IMU 2 Click is a compact add-on board for enhancing hardware prototypes with 6DOF functionality (6 degrees of freedom). This board features the BMI160, a small low-power inertial measurement unit (IMU) from Bosch Sensortec. It combines a state-of-the-art 3-axis low-g accelerometer and a low-power 3-axis gyroscope designed for 6-axis and 9-axis...
The mikroETH100 Board is an accessory board that contains ENC624J600 (stand-alone 10/100 Base-T Ethernet interface controller with integrated MAC & PHY, 24-Kbyte RAM buffer). Board is designed to serve as an Ethernet network interface for any microcontroller equipped with SPI
Standard Ethernet cable with roll-patent mechanism. It’s equipped with two RJ45 male connectors...
Thermo K Click is a compact add-on board that serves as a thermocouple type-K probe interface for temperature measurement. This board features the MCP9600, a thermocouple EMF to temperature converter from Microchip. With the versatile type-K probe, this board enables precise temperature measurements of up to +480 °C. However, the capabilities don't stop...
LSM6DSL click measures linear and angular velocity with six degrees of freedom. It carries the LSM6DSL high-performance 3-axis digital accelerometer and 3-axis digital gyroscope. The click is designed to run on a 3.3V power supply. LSM6DSL click communicates with the target microcontroller over SPI or I2C interface, with additional functionality provided...
Heart Rate 3 Click is a compact add-on board that can be used for heart-rate monitoring. This board features the SFH7050, a pulse oximetry and heart rate sensor from ams OSRAM. It provides excellent readings for different usage scenarios depending on the lighting conditions or skin tones. In addition, this Click board™ features the AFE4404, an ultra-small...
USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional functionality provided the following pins on the mikroBUS™ line: RST, CS, PWM, INT.
PIC18F87J60 microcontroller. It features IEEE 802.3™ Compatible Ethernet Controller with integrated MAC and 10Base-T PHY. It supports one 10Base-T port with activity outputs for 2 LED indicators.
Loading
Load more
Loading
