Filter Product By
Slide and select filter/s
Filtered by
The Single Cell click is a Click board™ which features MCP16251 synchronous boost regulator with true load disconnect and MCP1811A low-dropout (LDO) linear regulator that provide an ultra low quiescent current during device operation of about 250nA and can be shut down for 5nA (typical) supply current draw. Given the potential applications of these...
DAC 6 Click is a compact add-on board that contains a fully-featured, general-purpose voltage-output digital-to-analog converter. This board features the DAC104S085, 10-bit, micro-power, a quad digital-to-analog converter with rail-to-rail output, from Texas Instruments. It uses the 3-wire SPI serial interface for communication, that operates at clock...
UVA Click is a compact add-on board used to detect solar UV index. This board features the GUVA-C32SM, an ultraviolet light sensor capable of measuring UV index between 0 to 14 from GenUV. It contains the GaN-based chip die, amplifiers, ADC, digital control logic, and I2C interface circuit to measure UVA volumes, working in the spectral range of...
Angle 9 Click is a compact add-on board that detects the absolute position of a permanent magnet. This board features the AAS33001, a precision angle sensor with incremental and motor commutation outputs and on-chip linearization from Allegro Microsystems. It is a contactless angle sensor for 0° to 360° angular position, rotation speed, and directional...
6DOF IMU 23 Click is a compact add-on board for precise motion tracking and measurement. This board features the IIM-20670, a high-performance 6-axis MotionTracking device from TDK InvenSense that integrates a 3-axis gyroscope and a 3-axis accelerometer. The gyroscope offers a full-scale range of up to ±1966 dps with high accuracy, while the accelerometer...
GNSS RTK 4 Click is a compact add-on board designed for high-precision GNSS positioning with real-time kinematics (RTK) support. This board features the LG290P, a quad-band GNSS module from Quectel, capable of receiving signals from GPS, GLONASS, Galileo, BDS, QZSS, and NavIC while using SBAS for enhanced accuracy. This board supports multi-mode RTK...
Tamper click is equipped with SDS001, a low profile side-actuated detect switch, made by C&K company. This is a high-quality, low-current detection switch, which is designed in a form of a push button. The switch itself is very small - only 2mm of switch overtravel length, which coupled with its low actuation force, makes it ideal for using it as a...
Angle 8 Click is a compact add-on board that detects the absolute angular position of a permanent magnet. This board features the MA782GGU, a low-power angle sensor with integrated wake-up angle detection from Monolithic Power Systems. With its power cycling ability, the MA782GGU can be optimized for applications that require low average power. It...
This one is for all NECTO Studio IDE users and people who love wearing modern designs. This T-shirt is in blue color with the "Ideal way of coding" sign on the front and the MIKROE logo on the left sleeve. FEMALE SIZES CHART Size S M L XL XXL Lenght(cm) 63 65 67 68 70 Width(cm) 43 45 48 50 53 MALE...
Brushless 27 Click is a compact add-on board that controls DC brushless motors with any MCU. This board features the TMC6300, a power driver for BLDC/PMSM motors from Analog Devices. It is a highly efficient low voltage, zero standby driver for 3-phase BLDC/PMSM motors with up to 2A peak current. The triple half-bridge of this driver separates the HS and...
High Speed Thermal Print Head - 4.2V-9.5V (M23-DH-H69) is designed for fast, high-resolution thermal printing in compact electronic systems. It features a direct line thermal printing method with a resolution of 8 dots/mm, a 48mm maximum print width, and supports speeds up to 100mm/s. Operating within a voltage range of 4.2V to 9.5V, it includes a...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
The Buck 14 Click is a Click board™ based around the BMR4613001/001, a PoL regulator from Flex. It's high-efficiency step-down converter which provides a highly regulated output voltage derived from the connected power source, rated from 4.5 to 14V. The regulated output voltage can be selected between 0.6V and 5V. The Buck 14 click due to high efficiency...
Brushless 15 Click is a compact add-on board suitable for controlling BLDC motors with any MCU. This board features the TB9061AFNG, an automotive pre-driver that incorporates a sensorless controller for driving a 3-phase full-wave brushless DC motor from Toshiba Semiconductor. The TB9061AFNG achieves 120° rectangular wave motor control by using an input...
Step Down 8 Click is a compact add-on board that converts higher voltages into a lower voltage level. This board features the MAX25232, a mini buck converter from Analog Devices. It is designed to deliver up to 3A with 3.5V to 36V input voltages while using only 3.5μA quiescent current at no load. The MAX25232 integrates high-side and low-side switches...
MICRF TX Click is a compact add-on board designed as a powerful RF transmitter for data transmission over the 315MHz frequency band. This board features the MICRF112, a high-performance RF transmitter IC from Microchip, renowned for its efficiency in operation. This Click board™ stands out for its ease of use, requiring only a simple crystal oscillator to...
V to Hz 2 click is a device that converts an analog voltage input signal into a pulse wave signal of a certain frequency. It has a linear response, so applying a voltage in a range of 0 to 3.3V on its input, will result in generating the pulse train with frequency linearly proportional to the input voltage. This click features very good linearity, covers...
CAP Wheel 2 Click is a capacitive touch sensor with round-shaped electrodes integrated on a Click board™. This click can sense touch even through plastic, wood, or other dielectric materials, which can be used to protect the surface of the PCB and the sensor pad trace itself. Therefore, this Click board™ comes with overlay, made of plexiglass. Unlike the...
TMR Angle Click is a Click board™ perfectly suited for developing applications that range from steering angle applications with the highest functional safety requirements to motors for wipers, pumps and actuators and electric motors in general. This is thanks to the TLE5501, which is dedicated to any automotive but also industrial and consumer...
TFT Color Display with Touch Screen (3.5") is a color active matrix thin film transistor(TFT) liquid crystal display (LCD).
Multi Stepper Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S109AFTG, CLOCK-in controlled bipolar stepping motor driver from Toshiba Semiconductor. It supports a PWM constant-current control drive and allows from full-step up to 1/32 steps resolution for less motor noise and smoother control. It...
Ambient 19 Click is a compact add-on board used to measure the amount of the present ambient light. This board features the APM-16D24-310-DF8/TR8, a digital output ambient light and proximity sensor with an I2C interface and interrupt from Everlight Electronics. It has a flexible and wide operating range for the ambient light sensor with a maximum...
LED Driver 18 Click is a compact add-on board that simplifies the control of multiple LEDs. This board features the TLC5947, a 24-channel LED driver from Texas Instruments. Each channel is individually adjustable with 4096 pulse-width modulated (PWM) steps and has a programmable current value of all channels with a maximum of 30mA of LED current per...
Loading
Load more
Loading
