Filter Product By
Slide and select filter/s
Filtered by
MINI-M0 for STM32 MINI-M0 for STM32 is a small ARM® Cortex™-M0 development board containing STM32F051R8 microcontroller. It perfectly fits into standard DIP40 socket. Board is equipped with 16MHz SMD crystal oscillator, and 32.768KHz crystal which can be used for internal RTCC module. It has reset button and three signal LEDs. Board comes preprogrammed...
Alcohol Click is a compact add-on board that can detect the presence of alcohol gases. This board features MQ-3, an alcohol gas sensor from Zhengzhou Winsen Electronics Technology. The gas sensing layer on the MQ-3 sensor unit is made of Tin dioxide (SnO2), an inorganic compound with lower conductivity in clean air (the conductivity increases as the...
8x8 G click is a 64 LED matrix display Click board™, composed of SMD LEDs organized in 8 rows by 8 columns. It has a digital brightness control in 16 steps, it can control every LED in the display matrix independently, it blanks the display on power up to eliminate glitches and it requires a single resistor to control the current through all the LEDs at...
mikromedia workStation v7 provides full development environment for mikromedia boards. It features on-board debugger, multimedia modules, four mikroBUS™ sockets and a large breadboard area.
AC Current sensor is a non-invasive sensor for measuring alternating current. This split-core type of sensor can be clipped around either a live or neutral wire.
Signal Relay Click is a compact add-on board with four relays that any host microcontroller can control. This board features four G5V-1, an ultra-miniature, highly sensitive single-pole double-throw (SPDT) relay for signal circuits from Omron. The Signal Relay Click comes equipped with the 8-pin screw terminal, two for each relay. Through them, the relays...
3D Motion Click is a compact add-on board providing a fully integrated inertial measurement solution. This board features Microchip’s MM7150, a 9-axis sensor fusion motion module. The MM7150 is a complete self-contained solution comprising a 3-axis accelerometer, a gyroscope, a magnetometer, and an SSC7150 motion coprocessor. The motion coprocessor has...
Load cell click is a weight measurement click which utilizes a load cell element, in order to precisely measure the weight of an object. The Load Cell click can be used with the strain gauge type of load cells and can measure up to ±20mV or ±40mV of differential voltage. The strain gauge load cell is typically a circuit made of four strain gauges,...
GSM Booster is a pin-compatible replacement for Telit GM862-QUAD module while retaining the same form factor of this popular module. GSM Booster contains Telit’s new GL865-QUAD GSM module, MMCX GSM antenna connector, SIM card holder, etc.
Standard solderless breadboard. It has 2 power buses, 30 columns and 10 rows - a total of 400 contact points.
6DOF IMU 2 Click is a compact add-on board for enhancing hardware prototypes with 6DOF functionality (6 degrees of freedom). This board features the BMI160, a small low-power inertial measurement unit (IMU) from Bosch Sensortec. It combines a state-of-the-art 3-axis low-g accelerometer and a low-power 3-axis gyroscope designed for 6-axis and 9-axis...
The Easy8051 v6 is compatible with 14-, 16-, 20-, 28-, 40-pin PLCC44 and PLCC32 MCUs. It comes with an AT89S8253. The board has a USB 2.0 programmer and many peripherals such port expander, MENU and 4x4 keypads etc. Note: the COG display is not included in the package; instead the package includes an LCD 2x16 display.
HDC1000 Click is a compact add-on board representing a temperature and humidity sensing solution. This board features Texas Instruments’s HDC1000, a digital humidity sensor with an integrated temperature sensor providing excellent measurement accuracy at low power. The HDC1000 is characterized by its high accuracy (±3% RH and ±0.2°C over a wide operating...
PIC18F87J50 microcontroller. Featuring nanoWatt technology, it has up to 10 MIPS operation, 128K bytes of linear program memory, 3936 bytes of linear data memory, and lot of internal modules.
DAC 2 Click is a compact add-on board with a fully-featured digital-to-analog converter. This board features the LTC2601, a highly accurate 16-bit voltage-output digital-to-analog converter from Analog Devices. The LTC2601 has high rail-to-rail output drives and double-buffered data latches, communicating with the target MCU through the compatible SPI...
RN4678 Click is a compact add-on board that provides BT/BLE connectivity for any embedded application. This board features the RN4678, a Bluetooth 4.2 dual-mode module from Microchip. Data transfer is achieved through Bluetooth by sending or receiving data through SPP in Bluetooth (BT) Classic mode and Transparent UART in BLE mode. Over the onboard...
Ribbon Cable 40-wire, Female/Female, 20 cm
Ozone 2 click is an Ozone detection (O3) sensor, based on the MQ131 gas sensor. This gas sensor has a sensitive layer made of SnO2, which changes its resistance when exposed to ozone. The sensor is able to sense O3 concentration in the range of 10 ppm to 1000 ppm. The Click board™ is also equipped with a trimmer potentiometer, used to adjust the...
Note: This sensor is not recommended for new design. This product is obsolete. BlueTooth 2 Stick Board offers low power, highly economic wireless capability to your products. On-board WT41 offers impressive 1000 meters range between two bluetooth modules. It uses easy and simple UART protocol for communication.
Extension cable with jack (female) connector, (2.1x5.5x11-S to S/T) 2wc 0.2m. Operating temperature 0-40 °C.
Load cell 2 Click is a weight measurement click which utilizes a load cell element, in order to precisely measure the weight of an object. The Load Cell 2 Click can be used with the strain gauge type of load cells with external differential reference voltage range from 0.1V to 5V. The strain gauge load cell is typically a circuit made of four strain...
USB UART 2 click provides USB isolation and carries the ADUM4160BRWZ USB port isolator. The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over UART interface, with additional functionality provided the following pins on the mikroBUS™ line: RST, CS, PWM, INT.
The mikroETH100 Board is an accessory board that contains ENC624J600 (stand-alone 10/100 Base-T Ethernet interface controller with integrated MAC & PHY, 24-Kbyte RAM buffer). Board is designed to serve as an Ethernet network interface for any microcontroller equipped with SPI
Standard Ethernet cable with roll-patent mechanism. It’s equipped with two RJ45 male connectors...
Loading
Load more
Loading
