Additional library for MikroPascal PRO 2009

[mjoco]

Hi
Something is wrong. Yesterday I turned on the circuit, it worked well. Today the site is not loading and not responding to the ping. If I restart it then again works well. Did you not experience a mistake like this?
Greetings!

[Dany]

Hi
Something is wrong. Yesterday I turned on the circuit, it worked well. Today the site is not loading and not responding to the ping. If I restart it then again works well. Did you not experience a mistake like this?
Greetings!

No, I did'nt. Did you show your code already to Yo2Lio?

[mjoco]

Did you show your code already to Yo2Lio?

No, I did'nt.
I think that the error is in the electronic circuit, because he produced the same mistake, when I used the mP's SPI_Eth library. Then I thought that the problem is in the mE's library. So I started to use Yo2Lio's library.
I have built the circuit from the MikroPascal's Help, but I pulled the 74HCT245's OE pin to the GND.
Greetings!

[Donald Shimoda]

Do nothing, the library will not appear in library manager, the pack just put the library files in USES folder.
To use libraries, you must include this files at the beginning of program/units.

For example:

Code: Select all

uses pic_additional_string_library,Lib_Delays_LIO,lib1_18F97J60_V3_5,eth_lib_user,
     lib2_18F97J60_V3_5,def_io;

The problem with this , using MP PRO version 4.60 is, when you try to DEBUG the program using ICD, the compiler try to get the mpas version.

My code:

Code: Select all

uses
  pic_additional_string_library,Lib_Delays_LIO,
  lib1_enc28j60_V3_4,
  enc_lib_user,lib2_enc28j60_V3_4,
  definitions_ENC; // Don't touch this line !!!!!

When try to run on ICD MODE i get this error:

16 307 File "C:\Archivos de programa\Mikroelektronika\mikroPascal PRO for PIC\uses\P18\definitions_enc.mpas" not found PetroBoxTerm.mpas

As you can see, the compiler to debug take all the uses clauses like source code, dont compiled unit.

Any idea?

[RoMSI75]

As you can see, the compiler to debug take all the uses clauses like source code, dont compiled unit.
Any idea?

It happens to me also, I didn't try to understand, but I'm also waiting to find out why!!!

[janni]

As you can see, the compiler to debug take all the uses clauses like source code, dont compiled unit.

This usually happens when the lib was compiled with Release, not ICD Debug Built Type checked.

BTW, isn't there a source for ENC_V3_4 lib on Florin's page, here ?

[Donald Shimoda]

As you can see, the compiler to debug take all the uses clauses like source code, dont compiled unit.

This usually happens when the lib was compiled with Release, not ICD Debug Built Type checked.

I see, then is something to tell to Yo2lio, but i think is more friendly just "hidding" libraries without source code from the debug process, as delphi does.

Best regards.

[janni]

Obviously I was late adding to my previous message so I'll repeat - isn't there a source for ENC_V3_4 lib on Florin's page?

[Donald Shimoda]

Obviously I was late adding to my previous message so I'll repeat - isn't there a source for ENC_V3_4 lib on Florin's page?

AFAIK is closed source.

[janni]

Right, the sources have the same version number and file names, but were written for old mP .

[juanelectro]

Good day,

is there some way to know if connection fails to reset program with initial values and to recover connection?


Thanks for attention

[yo2lio]

is there some way to know if connection fails to reset program with initial values and to recover connection?

Hi,

Please be more specific. Do you refer at link up or down ?

[juanelectro]

Good day,

I send information from my own board to a server and sometimes board doesn't ping and it is necessary to reset it and connection comes back, it would be good to resolve problem in both situations (link up and down).


Thanks for attention.

[yo2lio]

New version available.

Additional library for MikroPascal PRO 2011 are available here :
http://www.microelemente.ro/MikroPascal ... y_V1_5.zip

All libraries recompiled with MP 4.60, debug mode.

Added ENC28J60 TCP/IP stack library for SPI2.

[Dany]

New version available.

Additional library for MikroPascal PRO 2011 are available here :
http://www.microelemente.ro/MikroPascal ... y_V1_5.zip

All libraries recompiled with MP 4.60, debug mode.

Added ENC28J60 TCP/IP stack library for SPI2.

Thanks Florin!