UDP Bootloader for PIC18 MCU with ENC28J60

[yo2lio]

Hello all

UDP Bootloader for PIC18 MCU with ENC28J60.

This program is only for P18 MCU
Tested with EasyPIC4 Board, MCU PIC18F452, clock 40 MHz ( 10x4 ) and Serial Ethernet Board ( ENC28J60 ).
Program use INT pin from ENC28J60. See the source code.

Thanks to ME teeam.

You have source code, hex file for PIC18F452, and exe file for WINDOWS.

Default IP is 192.168.1.250.
Program have 6.2 Kb in size, is located at the end of MCU memory.

WARNING : If yoy want to recompile this project IT'S OWN YOUR RISK !!!!!!!!!!!!!!!!
Only for advanced users.

You can download code from:

http://www.microelemente.ro/UDP_Boot_ENC28J60.zip

For more information please contact me: florin@microelemente.ro

Best regards Florin Medrea

[yo2lio]

New release are available here : http://www.microelemente.ro/UDP_Boot_ENC28J60_V3.zip

Added :
- Support for 128k MCU.
- Possibility to disable INT pin.

You have hex file for 32k, 64k and 128k MCU.

Software is OPEN SOURCE.

[Donald Shimoda]

New release are available here : http://www.microelemente.ro/UDP_Boot_ENC28J60_V3.zip

Added :
- Support for 128k MCU.
- Possibility to disable INT pin.

You have hex file for 32k, 64k and 128k MCU.

Software is OPEN SOURCE.

Great! Thanks!

Do you allow mw edit the code to allow have two ports in place of one?

[yo2lio]

Yes, is OPEN SOURCE.

[LGR]

Florin, do you have any plans for, or an idea of what it would take to port this to the PIC24?

[yo2lio]

Florin, do you have any plans for, or an idea of what it would take to port this to the PIC24?

Good question !

This month , NO !

First I must learn PIC24. It is possible in November or December .

[passicon]

Hello,

I haven't the MikroPascal licence (I have MikroC licence).

Somebody can compile the project for MCU PIC18F2620, clock 32 MHz ( 8x4 )


thanks you very much

best regards

[yo2lio]

HI, I have now UDP_Boot_ENC28J60_V5.

In this version I take into account bugs reported in latest ENC28J60 ERRATA.

Also configurations (IP, MAC, UDP PORT, ENC28J60 CS and RES pin) will be stored in PIC EEPROM.

In few days (2 or 3), this library with source code will be available on the forum.

[yo2lio]

Hi,

New version are available UDP_Boot_ENC28J60_V5.

Example is compiled for PIC18F2620 , Xtal 8X4 (32 Mhz).

Configuration is stored in EEprom starting at address $F0 :

Code: Select all

$F0 - IpAddress0
$F1 - IpAddress1
$F2 - IpAddress2
$F3 - IpAddress3
$F4 - UDP_High_Port
$F5 - UDP_Low_Port
$F6 - MacAddress4 (last 2 value)
$F7 - MacAddress5
$F8 - CS pin at PORTC (must be from 0,1,2,6,7)
$F9 - RESET pin at PORTC(must be from 0,1,2,6,7)

Default value stored in EEprom :
Ip : 192.168.1.250
UDP_Port : 10001
Mac : 0004A38F0001
Configuration : PORTC,1 - CS pin
Configuration : PORTC,0 - RESET pin

You can download source code from :
http://www.microelemente.ro/MikroPascal ... J60_V5.zip

[passicon]

thanks you!

It work's well and It is easy to use.

Everybody should use it!

[Dany]

Hi Florin, is there already an ENC28J60 version for mP PRO 2009?
Thanks!

[yo2lio]

Sorry, NO.

[picuser]

Hi,

New version are available UDP_Boot_ENC28J60_V5.

Example is compiled for PIC18F2620 , Xtal 8X4 (32 Mhz).

Configuration is stored in EEprom starting at address $F0 :

Code: Select all

$F0 - IpAddress0
$F1 - IpAddress1
$F2 - IpAddress2
$F3 - IpAddress3
$F4 - UDP_High_Port
$F5 - UDP_Low_Port
$F6 - MacAddress4 (last 2 value)
$F7 - MacAddress5
$F8 - CS pin at PORTC (must be from 0,1,2,6,7)
$F9 - RESET pin at PORTC(must be from 0,1,2,6,7)

Default value stored in EEprom :
Ip : 192.168.1.250
UDP_Port : 10001
Mac : 0004A38F0001
Configuration : PORTC,1 - CS pin
Configuration : PORTC,0 - RESET pin

You can download source code from :
http://www.microelemente.ro/MikroPascal ... J60_V5.zip

i just tried this UDP Bootloader.
it works great! thanks yo2lio for sharing.

[mernature]

Hello,

How can I adapt for Mikro basic ?

[forsa]

Hello
Using Mikropascal 5.61
In the folder .mpppi file can not for that.
İncluiding the files in to the new project would create.
When I compile .maps files not found error.
The project will use only 2 lines to pic18f4620 change.

Thanks you

Best Regards