I buy the speakup.
i make my project and record the commands and puts the serial command and then update.
all ok. but the board dont send the commant for uart , the uart only show ready.
which may be happening
kind regards.
a question
-
- Posts: 272
- Joined: 17 Feb 2009 02:39
- Location: Colombia
- Contact:
Re: a question
Hi,
Are you sure that the voice command has been recognized ?
When you assign an action to a specific pin, does that action perform ?
Regards,
Filip.
Are you sure that the voice command has been recognized ?
When you assign an action to a specific pin, does that action perform ?
Regards,
Filip.
-
- Posts: 272
- Joined: 17 Feb 2009 02:39
- Location: Colombia
- Contact:
Re: a question
Hello, yes the board recognized the command, if i put a led on IO1, i can tu tunn on, off, toggle, with voice command, but the board dont send te serial command, only send "Ready" when i turn on
but no the serial command , i try use usb with HID terminal but the boars send command but in hex and no similar that i copy in mu project.
Please tell me what can happend.
i attachemment my project
kind regdard
but no the serial command , i try use usb with HID terminal but the boars send command but in hex and no similar that i copy in mu project.
Please tell me what can happend.
i attachemment my project
kind regdard
Re: a question
Hello alcidesramos
Could you please re-upload your project as an attachment here?
It seems that there was an error when you first tried to upload it. I want to try to help.
Best Regards
Could you please re-upload your project as an attachment here?
It seems that there was an error when you first tried to upload it. I want to try to help.
Best Regards
My hobby is collecting MikroElektronika products.
Gotta catch them all!
Gotta catch them all!
Re: a question
Hi,
How are you receiving the index - by USART Terminal ?
If so, please have in mind to check the HEX representation of the data, as the index value starts from zero, which is a non-ASCII character.
Regards,
Filip.
How are you receiving the index - by USART Terminal ?
If so, please have in mind to check the HEX representation of the data, as the index value starts from zero, which is a non-ASCII character.
Regards,
Filip.
-
- Posts: 272
- Joined: 17 Feb 2009 02:39
- Location: Colombia
- Contact:
Re: a question
Hello very thank for your answer.
i record video.
the link is:
http://youtu.be/IGXEyI7yTsU
i show how i make the project and final use the speakup.
yes the board recognized the command, and work with pins IOX
But dont snef the index for uart terminal.
i only recive READY in the uart.
MIkroE please a solution.
i buy other board it arive this week, i try to compare.
kind regards.
Alcides Ramos
i record video.
the link is:
http://youtu.be/IGXEyI7yTsU
i show how i make the project and final use the speakup.
yes the board recognized the command, and work with pins IOX
But dont snef the index for uart terminal.
i only recive READY in the uart.
MIkroE please a solution.
i buy other board it arive this week, i try to compare.
kind regards.
Alcides Ramos
-
- Posts: 272
- Joined: 17 Feb 2009 02:39
- Location: Colombia
- Contact:
Re: a question
ok I thought I was sending the text that i put when recorded de command.
but the board send a number of 16 bit in the order i record the command.
today arrive my oher board. all it ok
thank you Mikroe.
Kind Regards
but the board send a number of 16 bit in the order i record the command.
today arrive my oher board. all it ok
thank you Mikroe.
Kind Regards