hi,
I was using the ARM Developer Mikroprog is all OK, but now recognizes the microcontroller (STM32F407VG)OK, but presents an Error 2.
I have already installed the drives again and Mikroprog program but continued to have the same error.
How could perform a test to confirm that the defect is in the Hardware Programmer?
Print the following error screen
Please I would like some help to solve the problem as soon as possible.
Thank you
mikroProg Error
mikroProg Error
- Attachments
-
- Error Mikroprog.png (89.84 KiB) Viewed 4731 times
- petar.timotijevic
- mikroElektronika team
- Posts: 1739
- Joined: 19 Feb 2014 13:46
- Location: Serbia
- Contact:
Re: mikroProg Error
Hi ORB11,
Please can you open ticket at Support Desk, we can continue conversation there.
MikroE Support Desk
http://www.mikroe.com/support/
Best regards,
Peter
Please can you open ticket at Support Desk, we can continue conversation there.
MikroE Support Desk
http://www.mikroe.com/support/
Best regards,
Peter
Re: mikroProg Error
I purchased mikroProg PIC. How can I provide mikroProg headers to the boards which I design. Provide a sample PIC18F circuit in which mikroProg header is provided with required components. I nned it to provide mikroProg connector in my designs so that it can be used for programming and debugging. Till now I was providing PICKit2 and PICKit3 headers.
[HW:] EasyPIC v7, mikroProg PIC, AVR, STM32, PSoC, Tiva, 8051
[SW:] mikroC PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroBasic PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroPascal PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
Visual GLCD, Visual TFT
[SW:] mikroC PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroBasic PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroPascal PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
Visual GLCD, Visual TFT
- petar.timotijevic
- mikroElektronika team
- Posts: 1739
- Joined: 19 Feb 2014 13:46
- Location: Serbia
- Contact:
Re: mikroProg Error
Hi,jayanthd wrote:I purchased mikroProg PIC. How can I provide mikroProg headers to the boards which I design. Provide a sample PIC18F circuit in which mikroProg header is provided with required components. I nned it to provide mikroProg connector in my designs so that it can be used for programming and debugging. Till now I was providing PICKit2 and PICKit3 headers.
Please see mikroProg for PIC User Manual document, there you can find informations about this.
Best regards,
Peter
Re: mikroProg Error
Why it is not printed on mikroProg like mikroProg PIC, mikroProg AVR. It is just printed mikroProg. I purchased all mikroProgs and it is difficult to find out which is which one.
[HW:] EasyPIC v7, mikroProg PIC, AVR, STM32, PSoC, Tiva, 8051
[SW:] mikroC PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroBasic PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroPascal PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
Visual GLCD, Visual TFT
[SW:] mikroC PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroBasic PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
mikroPascal PRO PIC, dsPIC, PIC32, AVR, ARM, 8051
Visual GLCD, Visual TFT
- petar.timotijevic
- mikroElektronika team
- Posts: 1739
- Joined: 19 Feb 2014 13:46
- Location: Serbia
- Contact:
Re: mikroProg Error
Hi,jayanthd wrote:Why it is not printed on mikroProg like mikroProg PIC, mikroProg AVR. It is just printed mikroProg. I purchased all mikroProgs and it is difficult to find out which is which one.
Yes, this is good question, I will suggest that.
Thank you for participating in the improvement of our products.
Best regards,
Peter
-
- Posts: 57
- Joined: 09 Oct 2014 17:39
Re: mikroProg Error
I've got same problem as ORB11 with Mikromedia on STM32F407VGT6 (chip erase and read work, write causing crash). But mikromedia plus with STM32F407ZG works fine! I set "Windows XP SP3" compatible mode for "mikroProg Suite For ARM.exe" and it seems to be working with STM32F407VGT6 (write works, board is alive).
- petar.timotijevic
- mikroElektronika team
- Posts: 1739
- Joined: 19 Feb 2014 13:46
- Location: Serbia
- Contact:
Re: mikroProg Error
Hi,HardWareMan wrote:I've got same problem as ORB11 with Mikromedia on STM32F407VGT6 (chip erase and read work, write causing crash). But mikromedia plus with STM32F407ZG works fine! I set "Windows XP SP3" compatible mode for "mikroProg Suite For ARM.exe" and it seems to be working with STM32F407VGT6 (write works, board is alive).
Please which MS Win OS version and mikroProg Suite version you have?
I'll report this behavior to our development team.
Best regards,
Peter
-
- Posts: 57
- Joined: 09 Oct 2014 17:39
Re: mikroProg Error
Ok, I'm using Windows 7 SP1 x64 and: