Please help change in mikroC pro to mikroC

[jikkyboy]

my code
/*


LCD Data D4-D7 connected to RB4-RB7
LCD RS -> RA0
LCD E -> RA1
Start/Stop Time Select -> RB3
Unit Min Switch -> RB0
Tens Min Switch -> RB1
Cancel Switch -> RB2
Relay -> RA3
*/

// LCD module connections
sbit LCD_RS at RA0_bit;
sbit LCD_EN at RA1_bit;
sbit LCD_D4 at RB4_bit;
sbit LCD_D5 at RB5_bit;
sbit LCD_D6 at RB6_bit;
sbit LCD_D7 at RB7_bit;
sbit LCD_RS_Direction at TRISA0_bit;
sbit LCD_EN_Direction at TRISA1_bit;
sbit LCD_D4_Direction at TRISB4_bit;
sbit LCD_D5_Direction at TRISB5_bit;
sbit LCD_D6_Direction at TRISB6_bit;
sbit LCD_D7_Direction at TRISB7_bit;
// End LCD module connections

// Tact switches and Relay ports
sbit Relay at RA3_bit;
sbit SS_Select at RB0_bit; // Start Stop Time Select
sbit Unit_Button at RB1_bit;
sbit Ten_Button at RB2_bit;


// Messages
char Message1[]="00-99 min Timer";
char Message2[]="Device ON";
char Message3[]="Device OFF";
char Message4[]="Set Time: min";
char Message5[]="Time Left: min";
unsigned short i, j, unit=0, ten=0, ON_OFF=0, index=0, clear, time;
char *digit = "00";
// 300ms Delay
void Delay_300(){
Delay_ms(300);
}

void Display_Digits(){
digit[1]=unit+48;
digit[0]=ten+48;
Lcd_Out(2,11,digit);
}

void start_timer(unsigned short tmin){
unsigned short temp1, temp2;
Relay = 1;
ON_OFF = 1;
Lcd_Cmd(_LCD_CLEAR);
Lcd_Out(1,1,Message2);
Lcd_Out(2,1,Message5);
OPTION_REG = 0x80 ;
INTCON = 0x90;
for (i=0; i< tmin; i++){
temp1 = (tmin-i)%10 ;
temp2 = (tmin-i)/10 ;
Lcd_Chr(2, 12, temp2+48);
Lcd_Chr(2, 13, temp1+48);
j=1;
do {
Delay_ms(1000);
j++;
} while(((j<=60) && (Clear ==0)));
if (Clear) {
Relay = 0;
Delay_ms(500);
Lcd_Out(1,1,Message3);
INTCON = 0x00;
goto stop;
}
}
stop: Relay = 0;
ON_OFF = 0;
unit = 0;
ten = 0;
clear = 1;
}

void interrupt(void){

if (INTCON.INTF == 1) // Check if INTF flag is set
{
Clear = 1;
INTCON.INTF = 0; // Clear interrupt flag before exiting ISR
}
}

void main() {
CMCON |= 7; // Disable Comparators
TRISB = 0b00001111;
TRISA = 0b11110000;
Relay = 0;

Lcd_Init(); // Initialize LCD
start:
clear = 0;
Lcd_Cmd(_LCD_CLEAR); // Clear display
Lcd_Cmd(_LCD_CURSOR_OFF); // Cursor off
Lcd_Out(1,1,Message1);
Lcd_Out(2,1,Message4);
Display_Digits() ;
do {

if(!Unit_Button){
Delay_300();
unit ++;
if(unit==10) unit=0;
Display_Digits();
} // If !Unit_Button

if(!Ten_Button){
Delay_300();
ten ++;
if(ten==10) ten=0;
Display_Digits();
} // If !Ten_Button

if(!SS_Select){
Delay_300();
time = ten*10+unit ;
if(time > 0) start_timer(time);
} // If !SS_Select

if(clear){

goto start;
}

} while(1);
}

[abcdefgg]

Hi,

Requests like this are often um...

Regards,

Abcdefgg