Hello,
I have a 32MZ1024ECM100 development board and easypic fusion v7. I want to programming 32MZ1024ECM100 with fusion v7 ext ICD output. my connection is good. there is no problem. but mikroprog suite give an interesting error like attached picture. I selected 32MZ1024ECM100 on mikrobasic pro for pic32 compiler, but mikroprog suite says; selected 32MZ1024ECG100
why?
about 32MZ2048ECM100 programming
about 32MZ2048ECM100 programming
- Attachments
-
- pic32_1.jpg (163.27 KiB) Viewed 5925 times
Last edited by MedBoy on 26 Apr 2016 12:37, edited 2 times in total.
- Aleksandar.Mitrovic
- mikroElektronika team
- Posts: 1697
- Joined: 11 Mar 2015 12:48
Re: about 32MZ2048ECM100 programming
Hi,
Are you using the latest version of our mikroProg Suite for PIC and compiler for PIC32?
Best regards,
Aleksandar
Are you using the latest version of our mikroProg Suite for PIC and compiler for PIC32?
Best regards,
Aleksandar
Re: about 32MZ2048ECM100 programming
Hi,Aleksandar.Mitrovic wrote:Hi,
Are you using the latest version of our mikroProg Suite for PIC and compiler for PIC32?
Best regards,
Aleksandar
The version of Pic32 compiler: 3.6.0 (it says up to date)
MikroProg Suite : 2.34
As you can see attached picture, there is no "M" series support. may be problem is that.
- Attachments
-
- Adsız.jpg (79.16 KiB) Viewed 5911 times
Re: about 32MZ2048ECM100 programming
It's obvious that you had version 2.34, it's the only one with PIC32MZ support. They ask that question because they don't have any answer for you. The next questions will be about ICSP connexion, power etc. You will lose many days before having a solution. The best way to speed up things is to open a ticket an then maybe...
Serge T.
Learning is an endeless process but it must start somewhere!
Learning is an endeless process but it must start somewhere!
- Aleksandar.Mitrovic
- mikroElektronika team
- Posts: 1697
- Joined: 11 Mar 2015 12:48
Re: about 32MZ2048ECM100 programming
Dear MedBoy,
The PIC32MZ1024ECM100 is supported in our mikroProg Suite version 2.34 as you can see on the picture below.
I will try to find same MCU and see if there is some problem in the Suite related to this chip.
Best regards,
Aleksandar
The PIC32MZ1024ECM100 is supported in our mikroProg Suite version 2.34 as you can see on the picture below.
I will try to find same MCU and see if there is some problem in the Suite related to this chip.
Best regards,
Aleksandar
- Attachments
-
- PIC32MZ.jpg (134.96 KiB) Viewed 5897 times
Re: about 32MZ2048ECM100 programming
Thanks for your interest Aleksandar. I am waiting your reply.Aleksandar.Mitrovic wrote:Dear MedBoy,
The PIC32MZ1024ECM100 is supported in our mikroProg Suite version 2.34 as you can see on the picture below.
I will try to find same MCU and see if there is some problem in the Suite related to this chip.
Best regards,
Aleksandar
- Aleksandar.Mitrovic
- mikroElektronika team
- Posts: 1697
- Joined: 11 Mar 2015 12:48
Re: about 32MZ2048ECM100 programming
Hi MedBoy,
Can you try to replace this Suite in the attachment with your exe and then try to program your MCU?
Best regards,
Aleksandar
Can you try to replace this Suite in the attachment with your exe and then try to program your MCU?
Best regards,
Aleksandar
- Attachments
-
- mikroProg Suite For PIC.rar
- (3.9 MiB) Downloaded 214 times
Re: about 32MZ2048ECM100 programming
Thanks Aleksandar. it worked. Anymore, i am programming the PIC32MZ2048ECM100 MCUAleksandar.Mitrovic wrote:Hi MedBoy,
Can you try to replace this Suite in the attachment with your exe and then try to program your MCU?
Best regards,
Aleksandar