Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Arduino IDE v2.0.4 on Windows 10.
Downloading works fine so long as only the "programming" USB port is connected;
If I have both the "programming" USB port and the "host/device" USB port connected, the download fails saying, "no device found" - despite the fact that the Windows Device Manager shows that both ports are connected:
The setups:
Downloading to a genuine Arduino DUE works fine in both cases.
Any ideas?
Downloading works fine so long as only the "programming" USB port is connected;
If I have both the "programming" USB port and the "host/device" USB port connected, the download fails saying, "no device found" - despite the fact that the Windows Device Manager shows that both ports are connected:
The setups:
Downloading to a genuine Arduino DUE works fine in both cases.
Any ideas?
- IvanJeremic
- mikroElektronika team
- Posts: 316
- Joined: 05 Sep 2022 14:32
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Hi,
Make sure that you are connected to the correct COM port when uploading the Sketch.
Worked fine for me when i tried connecting both connectors.
Also the two connectors do not have any connections between them, so i am not sure what would cause the issue regarding the HW.
Regards,
Ivan.
Make sure that you are connected to the correct COM port when uploading the Sketch.
Worked fine for me when i tried connecting both connectors.
Also the two connectors do not have any connections between them, so i am not sure what would cause the issue regarding the HW.
Regards,
Ivan.
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Yes - you can see in the screenshot that the "DUE Programming Port" is selected.IvanJeremic wrote: ↑06 Apr 2023 11:55Make sure that you are connected to the correct COM port when uploading the Sketch.
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
There's the circuitry around U4 - what's that doing?IvanJeremic wrote: ↑06 Apr 2023 11:55the two connectors do not have any connections between them, so i am not sure what would cause the issue regarding the HW.
It isn't quite the same as on the original DUE:
- IvanJeremic
- mikroElektronika team
- Posts: 316
- Joined: 05 Sep 2022 14:32
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Hi,
Can you tell me what is the HW version of your board?
Regards,
Ivan.
Can you tell me what is the HW version of your board?
Regards,
Ivan.
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Sorry, diverted to other projects.
"HW REV 1.01A"
- IvanJeremic
- mikroElektronika team
- Posts: 316
- Joined: 05 Sep 2022 14:32
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Hi,
That is the same version i have, can you send me a detailed picture of both sides of your Flip&Click?
Also try removing everything from the Flip&Click MikroBUSes when trying to program the board with both connectors plugged in.
Regards,
Ivan.
That is the same version i have, can you send me a detailed picture of both sides of your Flip&Click?
Also try removing everything from the Flip&Click MikroBUSes when trying to program the board with both connectors plugged in.
Regards,
Ivan.
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Maybe clearer without flash?
- Attachments
-
- Dsc_0004a.jpg (2.72 MiB) Viewed 1010 times
-
- Dsc_0005a.jpg (5.47 MiB) Viewed 1010 times
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
I can't remember if I did have anything plugged in or not - so will give it a go ...IvanJeremic wrote: ↑30 May 2023 08:19try removing everything from the Flip&Click MikroBUSes when trying to program the board with both connectors plugged in.
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
With everything removed from the Flip&Click MikroBUSes, I still get the same problem.
I have updated the Arduino IDE to v2.1.0 - still get the same problem.
I have updated the Arduino IDE to v2.1.0 - still get the same problem.
- IvanJeremic
- mikroElektronika team
- Posts: 316
- Joined: 05 Sep 2022 14:32
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Hi,
I checked the Flip&Click again, and this time i got the same issue as you, it looks like it worked for me the last time because my USB ports tend to bug out sometimes, and the COM port got bugged out when i tried programming, which is the same as if i didn't connect it at all.
Bad luck....
I have forwarded this to the HW team so they can take a look at the issue and come up with a new design for this board.
Thank you for telling us about this issue.
Regards,
Ivan.
I checked the Flip&Click again, and this time i got the same issue as you, it looks like it worked for me the last time because my USB ports tend to bug out sometimes, and the COM port got bugged out when i tried programming, which is the same as if i didn't connect it at all.
Bad luck....
I have forwarded this to the HW team so they can take a look at the issue and come up with a new design for this board.
Thank you for telling us about this issue.
Regards,
Ivan.
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Thanks for the update - glad to know it's not just me!
Please let me know if there's any workaround/repair found ...
You're welcome.
Please let me know if there's any workaround/repair found ...
- IvanJeremic
- mikroElektronika team
- Posts: 316
- Joined: 05 Sep 2022 14:32
Re: Flip&Click SAM3X Can't download from Arduino IDE with both USB ports connected
Hi,
When there is a new version you will probably get it as a replacement for the one that you have now.
Regards,
Ivan.
When there is a new version you will probably get it as a replacement for the one that you have now.
Regards,
Ivan.