Dear All:

I downloaded mikroC 4.6 from the web and recompile the program, now it works. I was using mikroC 3.8.

Regards
yhm

Hi:

I tried to compile pic18 as well as pic16, it give me the same error. Please see the attachment.

Thank.
yhm

Dear All:

i purchased two units of 18FJprog.

I set up ICD Debug and mikroICD, the 18FJprog report
Device Timeout.

Any solution?

Regards
yhm

Hi: I downloaded OSA version 22.11.2010 (__OSA_VERSION__ 101122). I used mikroC Pro 3.8. I tried to compile the example in osa\example\mikroc\ mikroC managed to generate lights_mikroc16.hex but there were errors: 68 324 Undeclared identifier 'w' in expression osa_pic18_mikroc.c 70 324 Undeclared ide...

Hi Ranko:

It is working now with easyLv-18F-v6. Thank you.

Regards
yhm

Hi Mr Ranko:

I used ICD3 to program PIC18. However, I could not get a working debugging environment using MPLAB. I have purchased 2 units of LvPICFlash recently for PIC18FxxJ11 development. Is there any solution that I can use to debug MCU application properly?

Regards
yhm

[attachment=0]icd.gif[/attachment]

I had set the ICD as shown above. Perform write again. However, pressing F9 still

mikroICD:
- Error Starting Debugger
- PIC Clock Error.

mikroElektronika ICD hardware not found

I have reinstall the compiler, flash programmer, etc. I am using EasyLV-18F v6 board.

Dear All: Referring to the post: http://www.mikroe.com/forum/viewtopic.php?f=101&t=25357&start=0&hilit=could+not+start+debugger I have the same problem. However, I am using PIC18F26J11 which need LV18PICFlash.exe. I did not see any ICD related string in the configuration bits panel. Please help. Tha...

Hi:

I will try. I think it is good to have a forum to share user library (mcl) so that library base for MikroC can be improved and expanded.

Regards
yhm

Hi:

I would like to write some libraries that to be used in mikroC. I could not see setting for me to set the library path for any linker. Any help? Thank.

Regards
yhm

Hi: I discovered that if I clean up the project folder "Clear Project Folder ...", then the HS setting is properly set in the flash programmer software. It means that if you setting the oscilloscope setting, the value is stored in the configuration but this is not read by the flash programmer softwa...

[quote][color=#0000BF]Opening the project under the same compiler version on another computer already doesn't change the project settings. Do you have some different experience with this?[/color][/quote] I am using mikroC Pro for PIC v3.8. I downloaded an example from your web site and try. I was us...

Hi: MCU name and oscillator frequency (inside Project Setting tab) shall be stored in new project file so that when the project is moved to other computer, the setting follows. Also, PicFlash should automatically select the best Oscillator setting or can be set via "Project Setting" tab so that it d...

Hi: I did this: void main() { OSCCON = 0x62; // Oscillator setting for 4 MHz ADCON1 |= 0x0F; // Configure AN pins as digital CMCON |= 7; // Disable comparators ... } I used 4 MHz Canned crystal oscillator on PICDEM 2 Plus demo board Regards YHM

Hi: I could reproduced the same problem when it occurred. I did not restarted computer then. After a few days (computer has been restarted many times), the problem has gone away. Will keep you inform and test it when it happens again. BTW, I was running at full access right. For the post above me, m...