Hi,
I'd like to know if it's possible to use a 16x4 LCD display with EasyPic5.
If it is, what kind os LCD should I buy ?
Tks !!!!
Robert
Search found 54 matches
- 10 May 2010 19:06
- Forum: Development Boards
- Topic: EasyPic5 with 16x4 LCD
- Replies: 2
- Views: 1601
- 03 May 2010 23:59
- Forum: mikroBasic PRO for PIC General
- Topic: In circuit programming
- Replies: 5
- Views: 2278
Re: In circuit programming
Hi Ionut, Thanks for helping!!! I did a research and it’s not a good idea the bootloader for 16F628. Even so far I didn’t understand completely how bootloader works… So I'm trying to understand how to use ICSP. I have a EasyPic5 and I'm thinking to make a cable with the 5 signals (+5, GND, CLK, DATA...
- 03 May 2010 04:08
- Forum: mikroBasic PRO for PIC General
- Topic: In circuit programming
- Replies: 5
- Views: 2278
Re: In circuit programming
Hi Ionut,
Is it possible to use bootloader with 16F628A?
I never did it before... Could you help me with some tips?
Thanks !!!!
Is it possible to use bootloader with 16F628A?
I never did it before... Could you help me with some tips?
Thanks !!!!
- 03 May 2010 00:05
- Forum: mikroBasic PRO for PIC General
- Topic: In circuit programming
- Replies: 5
- Views: 2278
In circuit programming
Hi, I developed a specific hardware and software using PIC16F628A and MikroB. Now I’d like to know how I should increment in the hardware for an in circuit programming using a USB cable or any other kind of cheap communication. I think I could do only one hardware for a USB communication and from th...
- 22 Dec 2008 23:18
- Forum: mikroBasic General
- Topic: Interrupt - PIC16F628A
- Replies: 3
- Views: 2135
- 22 Dec 2008 15:24
- Forum: mikroBasic General
- Topic: Interrupt - PIC16F628A
- Replies: 3
- Views: 2135
Interrupt - PIC16F628A
Hi guys! I have a simple question about interruption... I need to use TMR1 like a counter and TMR0 for interruption generation... So I did the following: sub procedure INTERRUPT() timer_count = timer_count +1 if timer_count = 800 then T1CON.0 = 0 INTCON.2 = 0 timer_count = 0 sample_tmp = TMR1reg TMR...
- 20 Dec 2008 14:29
- Forum: mikroBasic General
- Topic: Some questions about PIC16F628A hardware.
- Replies: 21
- Views: 8527
- 20 Dec 2008 14:10
- Forum: mikroBasic General
- Topic: How to get a specific bit of a word
- Replies: 6
- Views: 2654
Hi guys, I sove the problem but its not a general solution... like i need only the bit 0 of the most significant byte i just did this: PORTA.0 = sense_led.0 PORTA.1 = sense_led.1 PORTA.2 = sense_led.2 PORTA.3 = sense_led.3 PORTA.6 = sense_led.4 PORTA.7 = sense_led.5 PORTB.0 = sense_led.6 PORTB.1 = s...
- 20 Dec 2008 01:54
- Forum: mikroBasic General
- Topic: How to get a specific bit of a word
- Replies: 6
- Views: 2654
Hi Zan, Its a good idea but I need to send a specific bit from HiByte to a specific pin on the port, not to all port... so I tryed it and doesnt work... :( The problem is that the command PORTB.2 = sense_led.8 send the sense_led.0 bit to PORTB.2... I dont know way but always the program send the bit...
- 19 Dec 2008 22:50
- Forum: mikroBasic General
- Topic: How to get a specific bit of a word
- Replies: 6
- Views: 2654
How to get a specific bit of a word
Hi, I'm trying to white to a pin port a specific bit of a word variable but the program didnt reconize what I want... could someone helps me? See pre program: supose the sense_led = %0000000100000000 PORTA.0 = sense_led.0 PORTA.1 = sense_led.1 PORTA.2 = sense_led.2 PORTA.3 = sense_led.3 PORTA.6 = se...
- 19 Dec 2008 11:29
- Forum: mikroBasic General
- Topic: Some questions about PIC16F628A hardware.
- Replies: 21
- Views: 8527
Hi Raslan, I was considering using this configuration but I think when the RA4 goes to level 1 I’ll have no voltage on transistor base, so I’1l need a pull-up. If I use a resistor connected to 5V for a pull-up, the transistor will not close at all. My load is a 12V relay and using this configuration...
- 18 Dec 2008 18:10
- Forum: mikroBasic General
- Topic: Some questions about PIC16F628A hardware.
- Replies: 21
- Views: 8527
- 18 Dec 2008 16:55
- Forum: mikroBasic General
- Topic: Some questions about PIC16F628A hardware.
- Replies: 21
- Views: 8527
- 18 Dec 2008 14:35
- Forum: mikroBasic General
- Topic: Some questions about PIC16F628A hardware.
- Replies: 21
- Views: 8527
Some questions about PIC16F628A hardware.
Hi guys, I have 2 questions about PIC-16F628A hardware... 1) I read on data sheer the following: Peripheral Features - High current sink/source for direct LED drive Is it means I need no resistor to limit current? Could I connect the led direct to an output port? 2) RA4 is an open drain output. Coul...
- 16 Dec 2008 18:49
- Forum: Development Boards
- Topic: build type MikroICD for 16F628A
- Replies: 1
- Views: 1311
build type MikroICD for 16F628A
Hi,
I'm trying to use ICD debug with a 16F628A but i have a warning that this PIC does not support ICD debug... Is it right or i'm doing something wrong?
Could you help me ?
I'm trying to use ICD debug with a 16F628A but i have a warning that this PIC does not support ICD debug... Is it right or i'm doing something wrong?
Could you help me ?