hi friends,
any one can help me
Saran
Search found 90 matches
- 26 Jan 2011 13:12
- Forum: mikroC General
- Topic: pic 18f8520 configuration bits
- Replies: 2
- Views: 1764
- 26 Jan 2011 02:56
- Forum: mikroC General
- Topic: pic 18f8520 configuration bits
- Replies: 2
- Views: 1764
Re: pic 18f8520 configuration bits
hi friends,
anybody have suggestion for my problem, still i get struck
Saran
anybody have suggestion for my problem, still i get struck
Saran
- 25 Jan 2011 09:24
- Forum: mikroC General
- Topic: pic 18f8520 configuration bits
- Replies: 2
- Views: 1764
pic 18f8520 configuration bits
hi friends, i am using Mikro C, and big pic 5 development board, i am developing master/slave communication with RS 485 examples given by ME, i am using the PIC 18f8520, since the library function of micro c is in PORT C i use the RC6, RC7 as tx and RX and RC2 as ccp1. i use the port H as the I/O. w...
- 11 Mar 2009 13:04
- Forum: mikroC General
- Topic: Big Pic 5 not working
- Replies: 1
- Views: 1064
Big Pic 5 not working
Hi friends, recently i bought two big pic 5 development boards from ME, then i try the RS 485 expamples gave in the ME site. after i down load one kit with the master program and another kit with the slave kit. after i connect them with the two wires at the RS 485 terminals at the left hand side of ...
- 08 Mar 2009 09:38
- Forum: mikroC General
- Topic: VPP voltage error (5.6v)
- Replies: 4
- Views: 2058
- 07 Mar 2009 04:06
- Forum: mikroC General
- Topic: VPP voltage error (5.6v)
- Replies: 4
- Views: 2058
Hi Xor, thanks for the reply when i use the mcu card comes with the Big Pic 5 i can download and change other programs , no problem on it. once i start to use the new Big Pic mcu card with the PIC 16f946 then i face the problem. i dont see any short in the board. but the 16f946 is not in the list of...
- 06 Mar 2009 11:33
- Forum: mikroC General
- Topic: VPP voltage error (5.6v)
- Replies: 4
- Views: 2058
VPP voltage error (5.6v)
Hi friends, just i bought the Big Pic 5 development board, and i bought the Big pic MCU card, i solder all the capacitors, oscilator and solder the PIC 16F946 chip when i try to down load the program into the chip, i got the error of VPP voltage error (5.6v). can any one help me to fix the problem. ...
- 29 Dec 2008 09:06
- Forum: mikroC General
- Topic: Bad bit number - error
- Replies: 9
- Views: 3536
- 28 Dec 2008 14:30
- Forum: mikroC General
- Topic: Bad bit number - error
- Replies: 9
- Views: 3536
- 27 Dec 2008 08:20
- Forum: mikroC General
- Topic: Bad bit number - error
- Replies: 9
- Views: 3536
- 26 Dec 2008 16:17
- Forum: mikroC General
- Topic: Bad bit number - error
- Replies: 9
- Views: 3536
hi thank you very much for your concern, those masked lines are part of my codes, if i mask two more portion of my codes ( until scanning the RF1) there is no problem in the compiling the codes, when ever include my part of the codes the number of errors ( same error) are increasing, i am having the...
- 25 Dec 2008 15:06
- Forum: mikroC General
- Topic: Bad bit number - error
- Replies: 9
- Views: 3536
hi I am using the PIC 16F946 and i am using the easy pic 5 and the mikro C compiler, i have about 2600 lines of codes, if i mask rear portion of the codes and i dont have these error, when ever i add in the codes the number off same errors are getting more, is there any limitation in the number of l...
- 24 Dec 2008 13:30
- Forum: mikroC General
- Topic: Bad bit number - error
- Replies: 9
- Views: 3536
Bad bit number - error
Hi friends,
Merry Christmas,
when i compile my codes i have the error "bad bit number"
line/column is "1"
Message No is "0"
what should be the possible reason for this message
thanks again
Saran
Merry Christmas,
when i compile my codes i have the error "bad bit number"
line/column is "1"
Message No is "0"
what should be the possible reason for this message
thanks again
Saran
- 17 Dec 2008 12:22
- Forum: mikroC General
- Topic: mikro ICD debugger
- Replies: 0
- Views: 1050
mikro ICD debugger
I am using the easy pic 5, micro C compiler and pic 16f877a chip when i am using the debugger to debugg one program, for example if i press the RB0 then out put should be high at RD0 it is my logic the same come is working in other program so no doubt about the code, in the debugger mode, when i pre...
- 03 Dec 2008 12:42
- Forum: mikroC General
- Topic: SPI at the slave side
- Replies: 0
- Views: 989
SPI at the slave side
Hi friends, I am using the RS 485 and the SPI (port Expander) together for my application, when i use the SPI (port Expander) together with the master side of the RS 485 no problem with that, once i initialize the SPI(port Expander) in the slave side there is problem in the SPI(port Expander) i cann...