Ok Goran,

Thank you for your explanation.

Hello,

I want to make a software in the PIC 10F200 using MikroC, but when I start a new Project there is just PICs 12F, 16F or 18F.

In the PICFLASH there is this option (10F200).

How can I program the 10F200 using MikroC?

Hello, I'm doing a remote control and the first steps was making my own protocol with a startbit, 16 bits of the code plus a parity bit. I saw in this forum that some guys use Manchester code in remote controls, that looks like more reliable. So, to the experts: what is the best and reliable way to ...

Try the software and hardware shown in the address http://www.piclist.com/images/boards/irwidget/index.htm

Regards

Not yet, but I'll try.

thanks!

around, It is really very strange this behavior of DS1307. As the hardware was a prototype (all in modules) just to test the software I disassembled all and now I am making the PCB for it. But I did not tested with the address 0x07. I made the software just with examples I found on the internet beca...

I finally solve my problem. In the code to initialize I2C I just removed the last lines, like day, month, year, etc. I left just seconds, minutes and hours, as follows: I2C_Init(100000); I2C_Start( ); I2C_Wr(0xD0); I2C_Wr(0); I2C_Wr(0x00); I2C_Wr(0x15); I2C_Wr(0x10); I2C_Stop( ); And it is working w...

Very nice contribution.

I needed some code like your to get GPS information in my PIC project.

Regards!

Guys, I’m having some problems when I try to communicate my PIC 18F4520 with the DS1307 in a very simple clock. I configured normally the DS1307 as you can see below: I2C_Init(100000); I2C_Start( ); I2C_Wr(0xD0); I2C_Wr(0); I2C_Wr(0x00); I2C_Wr(0x15); I2C_Wr(0x10); I2C_Wr(0x00); I2C_Wr(0x00); I2C_Wr...

Kia,

Very good software!
This will help us a lot in the programming actions.

Regards.

Hello MasterBlaster, In the project settings I have the following checked items on 16F877A: - DEBUG OFF; - CPD OFF; - LVP OFF; - BODEN OFF; - PWRTE OFF; - WDT OFF; - HS OSC. The Pic Flash window during writing shows the 16F877A to be written. The MikroC installed is v8.2 and PicFlash is v7.11. I am ...

Guys, I'm having this problem sometimes. I'm using 16F877A for a project in the EasyPIC5. When I programm it to make the tests, sometimes appears the following message when trying to programm: Device detected: 12F508 Device selected: 16F877A If I close MikroC and turn off the EasyPIC5, and reopen bo...

If you use I2C commands to the DS1307 (by hardware) and Soft_I2C to other device (by software).

Is it possible???

Copy'nPaste, Today I used another power supply and the board worked fine. I could conclude that the problem was the power supply. This original power supply was made by myself, just to this use. It has a transformer, a bridge rectifier and a capacitor of 3300uF, not regulated and worked good for abo...

Guys, I had used my EasyPIC5 normally with USB line providing +5VCC to get the 5 Volts in the board. One week ago installed an external power supply, according board specified voltages (between 8 and 16 volts AC or DC). My external power supply give me about 12 volts. So, today, when I tried to prog...