Search found 10 matches
- 20 Dec 2013 21:27
- Forum: Development Boards
- Topic: GSM CLICK no response !!
- Replies: 7
- Views: 4399
Re: GSM CLICK no response !!
Hello Now the gsm module is working (i think), when I call to gsm it rings. But problem is that when I send AT command to gsm response from gsm is LF (hex = 0A , decimal = 10) Is this problem with wiering?? I have problem with poweron gsm pin, if I set it on, the control led does not light. But gsm ...
- 17 Dec 2013 18:56
- Forum: Development Boards
- Topic: GSM CLICK no response !!
- Replies: 7
- Views: 4399
Re: GSM CLICK no response !!
sorry i did NOT provide 3,3V
I will tray this
I wiil let you know
I will tray this
I wiil let you know
- 16 Dec 2013 09:42
- Forum: Development Boards
- Topic: GSM CLICK no response !!
- Replies: 7
- Views: 4399
Re: GSM CLICK no response !!
' * ' * Project name: ' GSM_Calling_Demo ' * Copyright: ' (c) MikroElektronika, 2005-2010. ' * Revision History: ' 20101110: ' - initial release (FJ); ' * Description: ' This is a simple project which demonstrates the use of Telit GM862-QUAD GSM module ' Upon programming the MCU, connect your Telit...
- 15 Dec 2013 13:51
- Forum: Development Boards
- Topic: GSM CLICK no response !!
- Replies: 7
- Views: 4399
GSM CLICK no response !!
Hello! I have problem with gsm click. I cannot start it?? I have old easyavr5 bord. A connect all connections to board. VCC, GND, power supplay 5V RX (gsm) PORTD1 TX (gsm) PORTD0 CTS PORTC4 GP2 PORTD4 (what is this signal??) RTS PORTC5 RST no coonected (is this ok??) PWR PORTC6 I tried with code fro...
- 16 Jan 2010 18:26
- Forum: mikroBasic PRO for AVR General
- Topic: Command clrwdt () doesnt work??
- Replies: 1
- Views: 2166
Command clrwdt () doesnt work??
Command clrwdt () doesnt work??
How to reset watchdog??
It only works if I stop watchdog and start it agen??
How to reset watchdog??
It only works if I stop watchdog and start it agen??
- 10 Jan 2009 12:16
- Forum: mikroBasic PRO for AVR General
- Topic: LCD command
- Replies: 1
- Views: 2574
LCD command
I have a lot of problems with basic pro!!!! When I write a lot of lcd_out the program is ob but on a easyavr the lcd frizes!!! :shock: :shock: whay did you change the commands???? The comands MUST stay the same so that no need of adisional learning some GOOD comands Lcd_init (porta , 3 , 2 , lcd_hi_...
- 09 Jan 2009 15:53
- Forum: mikroBasic PRO for AVR General
- Topic: problem with BUTTON command
- Replies: 2
- Views: 2805
I have solved the problem this way!! The same problem is with ow_wire becuose you can have only ONE line for one wire!! some times i need two so thah the aplication is better!!! (long conection) I also don't know how to display on lcd variable FF (hex) dec 255 in a dec do problem!! Before I used Byt...
- 09 Jan 2009 14:11
- Forum: mikroBasic PRO for AVR General
- Topic: problem with BUTTON command
- Replies: 2
- Views: 2805
problem with BUTTON command
I have 5 buttons on my maschine
with old microbasic there was no problem
If button (portc.1 , 100 , 1 , 1) then
xxx
end if
Now i can use only one button!!!
How to yuse more buttons!!!!
if posible to make the button comand as it was!!!
Thank you!!!
with old microbasic there was no problem
If button (portc.1 , 100 , 1 , 1) then
xxx
end if
Now i can use only one button!!!
How to yuse more buttons!!!!
if posible to make the button comand as it was!!!
Thank you!!!
- 06 Feb 2008 13:19
- Forum: mikroBasic General
- Topic: MIKROBASIC WITH SHT11 PROGRAMMING
- Replies: 18
- Views: 16214
hi
code would be useful!! I had the same problem with this sensor, but a have made the the code step by step (if you have easypic) you can monitor the sensor by lowering the frequancy (so that by each line you enter delay 1s) so you can see where is the problem!! i can send you code for AVR but a have ...
- 27 Jan 2008 15:51
- Forum: mikroBasic for AVR Wish List
- Topic: code for humidity sensors sht11 /sht 71
- Replies: 1
- Views: 5380
code for humidity sensors sht11 /sht 71
easier code for sensors SHT11 sensirion so that it can be programed as 1-wire standard it would be useful
marko
marko