Search found 69 matches
- 17 Dec 2019 14:20
- Forum: ARM AI Compilers
- Topic: Supported Mcus
- Replies: 6
- Views: 2884
Re: Supported Mcus
Thanks for the info and the fast reply!
- 16 Dec 2019 15:00
- Forum: ARM AI Compilers
- Topic: Supported Mcus
- Replies: 6
- Views: 2884
Supported Mcus
Hi folks. First off all, congrats on the update! I noticed from the list of supported mcus that only STMicroelectronics STM32s appear. Are there any plans to support TIVA TM4s such as TM4C129? Also, will there be compatibility with previous developments boards like EasyMxPROv7 for TIVA? What about t...
- 22 May 2019 12:57
- Forum: mikroC PRO for ARM General
- Topic: Help with 2.8-inch Riverdi Display
- Replies: 7
- Views: 1960
Re: Help with 2.8-inch Riverdi Display
Hi Stefan, thanks for the quick reply.
I read the article, but I was hoping (since it is posted a year ago) that something had changed, that someone made a workaround or something like that.
Also, thanks for the 320 x 320 tip.
Have a nice day!
I read the article, but I was hoping (since it is posted a year ago) that something had changed, that someone made a workaround or something like that.
Also, thanks for the 320 x 320 tip.
Have a nice day!
- 21 May 2019 22:33
- Forum: mikroC PRO for ARM General
- Topic: Help with 2.8-inch Riverdi Display
- Replies: 7
- Views: 1960
Re: Help with 2.8-inch Riverdi Display
Thanks very much for the reply. I had already noticed the SDO pin mistake, but it still had not worked. The absence of the second SPI configuration call and the unecessary FT800_Init() call really made the difference! Thanks for the example, it is working now! But I have another question. Does this ...
- 20 May 2019 22:59
- Forum: mikroC PRO for ARM General
- Topic: Help with 2.8-inch Riverdi Display
- Replies: 7
- Views: 1960
Re: Help with 2.8-inch Riverdi Display
Hi Stefan, thanks for the reply! I actually had seen this link, and even tried to implement this code. I also tried to make a code similar code myself, based on a code provided on the Riverdi Datasheet. But I could not get any of them to work. I probably made a mistake transforming the sample code o...
- 16 May 2019 20:45
- Forum: mikroC PRO for ARM General
- Topic: Help with 2.8-inch Riverdi Display
- Replies: 7
- Views: 1960
Help with 2.8-inch Riverdi Display
Hello everyone, I bought the Riverdi Display 2.8-inch UXB display (RVT28UEFNWC0x) from mikroE (https://www.mikroe.com/riverdi-28-uxb), but I can't make it work properly. The display turns on but stays on a white screen, not displaying my objects or the calibration screen. I'm programming in C, via m...
- 13 Jun 2018 13:31
- Forum: Visual TFT General
- Topic: Visual tft ft813 image show problem
- Replies: 57
- Views: 21397
Re: Visual tft ft813 image show problem
Hi folks.
Any findings?
I´m having the same problem here!
Any findings?
I´m having the same problem here!
- 08 May 2018 17:58
- Forum: mikroC PRO for ARM General
- Topic: Ethernet Connector Board Problem
- Replies: 11
- Views: 3521
Re: Ethernet Connector Board Problem
Thanks for the answer! Acctually, I simple connected those lines (and the RST Pin) of the processor by wire jumpers, out of the EasyMx Board, since i do not have access to those ETH pins on the EasyMx Board. I tested some digital pin and they are working, so the processor is working too. Where shoul...
- 07 May 2018 19:22
- Forum: mikroC PRO for ARM General
- Topic: Ethernet Connector Board Problem
- Replies: 11
- Views: 3521
Re: Ethernet Connector Board Problem
Sure! Is that enough?
- 04 May 2018 20:46
- Forum: mikroC PRO for ARM General
- Topic: Ethernet Connector Board Problem
- Replies: 11
- Views: 3521
Ethernet Connector Board Problem
Hi folks. I have managed to successfully run a code to work with the Intern-ETH, using EasyMx PRO v7 for Tiva ARM, with TM4C129X. Here is my code: #include "__Ethernet_Intern.h" const code unsigned char httpHeader[] = "HTTP/1.1 200 OK\nContent-type: text/plain\nAccess-Control-Allow-Origin: *\n\n"; u...
- 11 Apr 2018 23:55
- Forum: mikroC PRO for ARM General
- Topic: Config Timer on Input Edge-Count Mode
- Replies: 1
- Views: 1169
Config Timer on Input Edge-Count Mode
Hi, i´m using a Tiva TM4C129X on EasyMx Pro v7 for TIVA ARM. I made a Input Edge-Count Mode, up-count, on my PB2 port (T5CCP0). I have to read a 30 Khz pulse with 50% duty cycle, so counting on interrupt is not viable (there is not enought time) Maybe it will be helpful to someone else. Here is my c...
- 15 Sep 2017 15:10
- Forum: Development Boards
- Topic: Sourcing the Ethernet Connector LPJ0026GENL
- Replies: 7
- Views: 4489
- 14 Sep 2017 15:06
- Forum: Development Boards
- Topic: Sourcing the Ethernet Connector LPJ0026GENL
- Replies: 7
- Views: 4489
Re: Sourcing the Ethernet Connector LPJ0026GENL
Hi, I also need information about where can I buy this connector. I'm in Brazil, but I'm willing to import it.
Thanks!
Thanks!
- 10 Jul 2017 23:52
- Forum: mikroC PRO for ARM General
- Topic: Programming directly on a Tiva TM4C129XNCZAD
- Replies: 1
- Views: 2139
Programming directly on a Tiva TM4C129XNCZAD
Hi folks. I´m wondering here... Can I use the mikroC compiler for programming directly on a Tiva TM4C129XNCZAD (supported MCU) that i soldered on a Empty MCU card for TM4C129 series? Should I simply put it on Easy and program normally? Or do I need to install some kind of bootloader on the processor...
- 29 Jun 2017 23:04
- Forum: mikroC PRO for ARM General
- Topic: ETH ports Access
- Replies: 1
- Views: 1458
ETH ports Access
Hi Guys, i just bought the EasyMx PRO v7 for Tiva with the TM4C129XNCZAD mcu card, and i´m trying to access the 4 ports on the top of the left part of it ( RXP , RXM . TXP and TXM ). How do i do the software declaration for access that? I got the DP (USB-D_P - C18 - PL6) and DN (USB-D_N - B18 - PL7)...