Search found 433 matches
- 10 Dec 2010 10:22
- Forum: mikroC PRO for PIC General
- Topic: Problem with structure in "code" area
- Replies: 6
- Views: 2297
Re: Problem with structure in "code" area
Hello Danielz, I've tested your code in software simulator within our compiler and it's working fine. Although you have another h file included in program source code that is not available in project folder ( lianbiao.h ). What software simulator are you using? All this is working correct on our har...
- 10 Dec 2010 09:52
- Forum: Development Boards
- Topic: 5v - 3.3v and 3.3v - 5v translator boards
- Replies: 1
- Views: 1074
Re: 5v - 3.3v and 3.3v - 5v translator boards
Hello DonRecardo,
For now there is only pdf with schematic. The Datasheet will be soon released. Thank you for noticing this.
Best regards
For now there is only pdf with schematic. The Datasheet will be soon released. Thank you for noticing this.
Best regards
- 10 Dec 2010 09:30
- Forum: Development Boards
- Topic: Can't install Armprog on WinXP
- Replies: 3
- Views: 1738
- 09 Dec 2010 16:15
- Forum: mikroC PRO for PIC General
- Topic: Problem with structure in "code" area
- Replies: 6
- Views: 2297
Re: Problem with structure in "code" area
Hello Danielz , I have tested it and it is working fine. I used PIC16F887 @ 8MHz and EasyPIC6 Development board. I changed result variable with Ports A ( part1 ), B ( part2 ), C ( part3 ) and D ( part4 ) to easier monitor it. I got on Port A and C 0b00000111 , corresponds to decimal 7 , and on Port ...
- 09 Dec 2010 15:54
- Forum: Development Boards
- Topic: Can't install Armprog on WinXP
- Replies: 3
- Views: 1738
Re: Can't install Armprog on WinXP
Hello boattow , Please specify exact name of your ARM programmer hardware. Is it ARMFlash Programmer ? In any case, it should work with no problem on Windows XP operating system. Is it 32 or 64 bit? Uninstall all previous software, reinstall it again after restart and try programmer if it is recogni...
- 09 Dec 2010 15:06
- Forum: mikroBasic PRO for PIC General
- Topic: MBpro v4.15 not saving before rebuild? Also project paths
- Replies: 13
- Views: 3559
Re: MBpro v4.15 not saving before rebuild? Also project path
Hello oliverb,
Our Software bundle has integrated relative paths and by default whole project is stored like this. So if you have need to move your project folder, project manager will maintain all paths within folder.
Best regards
Our Software bundle has integrated relative paths and by default whole project is stored like this. So if you have need to move your project folder, project manager will maintain all paths within folder.
Best regards
- 09 Dec 2010 15:01
- Forum: Development Boards
- Topic: Can't get PIC24FJ96GA008 to do anything
- Replies: 3
- Views: 1544
Re: Can't get PIC24FJ96GA008 to do anything
Hello Filip, I'm sure you mistyped AD1PCFG , it should stand ADPCFG . In your while statement there is no change, so MCU executes code until this loop and is stuck doing nothing. You should change { ; } with { LATB = ~LATB; Delay_ms(250); // Delay of 250ms } so it has some effect. There is attached ...
- 09 Dec 2010 14:39
- Forum: mikroC PRO for PIC General
- Topic: Trouble writing to SD/MMC
- Replies: 5
- Views: 2263
Re: Trouble writing to SD/MMC
Hello Pav,
Please try out examples that come within our software bundle. You can find those under Extra Boards example folder.
Best regards
Please try out examples that come within our software bundle. You can find those under Extra Boards example folder.
Best regards
- 08 Dec 2010 16:07
- Forum: mikroC PRO for PIC General
- Topic: EEPROM+LCD Problem
- Replies: 2
- Views: 1601
Re: EEPROM+LCD Problem
Hello Try changing Lcd_Out(1,1,pass); with for(i=0; i<=5; i++) { Lcd_Chr(1,1+i,pass[i]); Delay_ms(10); // this line is not needed, but to give some delay to LCD } This will print one by one char from EEPROM locations. Also, please tell us what MCU are you using. Perhaps you could zip whole project f...
- 08 Dec 2010 10:39
- Forum: mikroBasic PRO for PIC General
- Topic: MBpro v4.15 not saving before rebuild? Also project paths
- Replies: 13
- Views: 3559
Re: MBpro v4.15 not saving before rebuild? Also project path
Hello, It has been tested and situation is like this. Regarding saving after changes, it does save while building and project has newest changed data. So this is not an issue. But if project is held on server hard drive, as in case that oliverb has, by reopening the project, main file must be manual...
- 03 Dec 2010 13:38
- Forum: mikroC PRO for dsPIC30/33 and PIC24 General
- Topic: function SPI2_Init_Advanced affects SPI1 I/O
- Replies: 1
- Views: 1398
Re: function SPI2_Init_Advanced affects SPI1 I/O
Hello JungleCoder,
I tried your code and it compiled without errors, even with TRISF2_bit = 0; after SPI initialization. Also code was tested on hardware and it works as it should.
In order to inspect your problem, please zip your whole project and attach it to this thread.
Best regards
I tried your code and it compiled without errors, even with TRISF2_bit = 0; after SPI initialization. Also code was tested on hardware and it works as it should.
In order to inspect your problem, please zip your whole project and attach it to this thread.
Best regards
- 03 Dec 2010 11:54
- Forum: mikroC PRO for AVR General
- Topic: Call signature does not match the function definition
- Replies: 14
- Views: 4892
Re: Call signature does not match the function definition
Hello granel , It seems that you didn't enable SSA Optimization . All function prototypes and function pointers have to be built using the same optimizer because of different calling conventions in different optimizers. In SSA, function parameters are passed via working registers, and without SSA th...
- 02 Dec 2010 12:58
- Forum: mikroC PRO for PIC General
- Topic: Trouble checking status of a button
- Replies: 2
- Views: 1375
Re: Trouble checking status of a button
Hello Anilsone.ca , First program code is OK. But you'll need to pull up or down Button pin over resistor to Vcc or GND. Here is how to do Pull-Down to GND. pin.PNG For Pull-Up, just change positions of Resistor and Switch. In second code, for PORTB to be output, you'll need to put TRISB = 0x00; ins...
- 02 Dec 2010 12:37
- Forum: mikroC PRO for AVR General
- Topic: Call signature does not match the function definition
- Replies: 14
- Views: 4892
Re: Call signature does not match the function definition
Hello granel,
I've tested your source code and it's working, but unfortunately I couldn't see your settings. Please attach your whole project, with settings etc. Best is to zip whole folder in which your source code is located.
Best regards
I've tested your source code and it's working, but unfortunately I couldn't see your settings. Please attach your whole project, with settings etc. Best is to zip whole folder in which your source code is located.
Best regards
- 01 Dec 2010 13:05
- Forum: mikroC PRO for dsPIC30/33 and PIC24 General
- Topic: Poer expander question
- Replies: 3
- Views: 1904
Re: Poer expander question
Hello Berkl , Here are possible solutions. One is to use hardware addresses of Port Expander modules, all connected to same SPI lines and while addressing modules you'll need to specify hardware address of module that needs to respond. Second solution is the one you are wishing to use. Every Port Ex...