SPI Isolator 8 Click

How does it work?

SPI Isolator 8 Click is based on the ISOW7743, a quad-channel digital isolator from Texas Instruments. The ISOW7743 is galvanically isolated and comes with an integrated high-efficiency DC-DC power converter with low emissions, which provides up to 550mW of isolated power. This way, the SPI Isolator 8 Click eliminates the need for a separate isolated power supply in space-constrained isolated designs. The integrated signal isolation channels employ an ON-OFF keying (OOK) modulation scheme to transmit data across a silicon-dioxide based isolation barrier. The transmitter sends a high-frequency carrier across the barrier to represent one state and sends no signal to represent the other state, while the receiver demodulates the signal after signal conditioning and produces the output through a buffer stage.

There are a few jumpers that allow you to use some of the isolator’s features. The VIN SEL allows you to choose the supply voltage for isolation channels between the external and ISOW7743’s converter output voltage. As external, you can use the voltages in a range of 2.25 – 5.5V. The VOUT SEL jumper allows you to choose the ISOW7743’s converter output voltage level. You can connect the external SPI device over the screw terminal. Besides, you can also connect an external power supply over the VEXT screw terminal, and isolated SPI device enable logic over the EN2 terminal. Over the VOUT terminal, you can power the connected SPI device.

SPI Isolator 8 Click uses a standard 4-Wire SPI serial interface to establish communication between the host MCU and the connected SPI device that needs to be isolated. The isolator features a multifunctional power converter enable input pin, that also serves as a fault output pin. Obviously, you can not use both at the same time. Those functions are available on pins ENP and FLT of the mikroBUS™ socket. To enable the host MCU side of the SPI Isolator 8 Click, you can use the ENC pin with a HIGH logic state.

This Click board™ can operate with either 3.3V or 5V logic and power voltage levels selected via the VIO and VCC SEL jumpers. This way, both 3.3V and 5V capable MCUs can use the communication lines properly. Also, this Click board™ comes equipped with a library containing easy-to-use functions and an example code that can be used, as a reference, for further development.

Specifications

Pinout diagram

This table shows how the pinout on SPI Isolator 8 Click corresponds to the pinout on the mikroBUS™ socket (the latter shown in the two middle columns).

Notes	Pin					Pin	Notes
ISOW7741 Enable	ENC	1	AN	PWM	16	ENP	DC-DC Converter Enable
Reset / ID SEL	RST	2	RST	INT	15	FLT	Fault Interrupt
SPI Chip Select / ID COMM	CS	3	CS	RX	14	NC
SPI Clock	SCK	4	SCK	TX	13	NC
SPI Data OUT	SDO	5	MISO	SCL	12	NC
SPI Data IN	SDI	6	MOSI	SDA	11	NC
Power Supply	3.3V	7	3.3V	5V	10	5V	Power Supply
Ground	GND	8	GND	GND	9	GND	Ground

Onboard settings and indicators

SPI Isolator 8 Click electrical specifications

Software Support

We provide a library for the SPI Isolator 8 Click as well as a demo application (example), developed using MIKROE compilers. The demo can run on all the main MIKROE development boards.

Package can be downloaded/installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on Mikroe github account.

Library Description

This library contains API for SPI Isolator 8 Click driver.

Key functions

• spiisolator8_transfer SPI Isolator 8 data transfer function.

• spiisolator8_enc_enable SPI Isolator 8 enable side 1 function.

• spiisolator8_enp_enable SPI Isolator 8 enable side 2 function.

Example Description

This example demonstrates the use of SPI Isolator 8 Click board™ by reading the manufacturer ID and device ID of the connected Flash 11 Click board™.

void application_task ( void ) 
 { 
     static uint8_t cmd_get_id[ 6 ] = { FLASH11_CMD_GET_ID }; 
     static uint8_t read_id[ 6 ] = { 0 }; 
     if ( SPIISOLATOR8_OK == spiisolator8_transfer( &spiisolator8, &cmd_get_id[ 0 ], &read_id[ 0 ], 6 ) ) 
     { 
         if ( ( FLASH11_MANUFACTURER_ID == read_id[ 4 ] ) && ( FLASH11_DEVICE_ID == read_id[ 5 ] ) ) 
         { 
             log_printf( &logger, " Manufacturer ID: 0x%.2Xrn", ( uint16_t ) read_id[ 4 ] ); 
             log_printf( &logger, " Device ID: 0x%.2X    rn", ( uint16_t ) read_id[ 5 ] ); 
             log_printf( &logger, " -----------------------rn" ); 
             Delay_ms( 3000 ); 
         } 
     } 
 }

The full application code, and ready to use projects can be installed directly from NECTO Studio Package Manager (recommended), downloaded from our LibStock™ or found on Mikroe github account.

Other Mikroe Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.SPIIsolator8

Additional notes and informations

Depending on the development board you are using, you may need USB UART click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. UART terminal is available in all MIKROE compilers.

mikroSDK

This Click board™ is supported with mikroSDK - MIKROE Software Development Kit. To ensure proper operation of mikroSDK compliant Click board™ demo applications, mikroSDK should be downloaded from the LibStock and installed for the compiler you are using.

For more information about mikroSDK, visit the official page.