Filter Product By
Slide and select filter/s
Filtered by
Categories
Mikroe has collaborated closely with onsemi to offer you a broad portfolio of products from this vendor, which will help you reducing development effort and accelerate time to market. As a 3rd party tool provider we strive to promote partners newest theologies and products, by offering them to the broad market.
4x4 Click is a compact add-on board that integrates 16 buttons into one design. This board features a 4x4 button keyboard with debounce circuits, and two MC74HC165A, 8-bit parallel-in/serial-out shift registers from onsemi. This 4x4 matrix keyboard allows multiple key presses simultaneously, where each button has its silkscreen marking. This Click board™...
BATT-MON 5 Click is a compact add-on board designed for precise fuel gauging of 1-cell Lithium-ion/Polymer (Li+) batteries. This board features the LC709204V from onsemi based on the innovative HG-CVR2 algorithm to deliver accurate Relative State of Charge (RSOC) readings under varying conditions, such as temperature changes, load fluctuations, and...
Brushless 16 Click is a compact add-on board suitable for controlling BLDC motors with any MCU. This board features the LB11685AV, a three-phase full-wave current-linear-drive motor driver from onsemi. It adopts a sensorless control system without the use of a Hall Effect device. The LB11685AV features a current soft switching circuit for quieter...
The CAN FD 4 Click is a Click board™ that features the NCV7344D10R2G, a Controller Area Network (CAN) transceiver, from onsemi. This Click board™ provides differential transmit capability to the bus and differential receive capability to the CAN controller. The CAN FD 4 click can be used for various applications such as automotive and industrial...
Comparator Click is a compact add-on board that contains two independent precision voltage comparators. This board features the LM2903, a dual differential comparator from onsemi. It provides two pair of screw terminals that allows you to connect separate inputs with additional ground connections, which let you use either a single (range of 2 to 36VDC) or...
Current 2 click is an accurate current sensing Click board™ suitable for a very accurate measurement of the current through the load. It utilizes the high-side current sensing approach, which has a few advantages over the low-side current sensing. Current 2 click is equipped with an integrated transimpedance amplifying circuit, designed specifically for...
EEPROM 10 Click is a compact add-on board that contains the highest-density memory solution. This board features the N24C32, a 32Kb I2C CMOS Serial EEPROM from onsemi. It is internally organized as 128 pages of 32 bytes each, with a 32-byte page write buffer and a fast write time of up to 4ms. It lasts one million full-memory read/writes/erase cycles with...
EEPROM 8 Click is a compact add-on board that contains a highly reliable nonvolatile memory solution. This board features the CAV24C512, a 512-Kb electrically erasable programmable memory with enhanced hardware write protection for entire memory from onsemi. Internally organized as 65,536 words of 8 bits each, the CAV24C512 comes up with the compatible...
eFuse 3 Click is a compact add-on board that contains an electronic eFuse. This board features the NIS6150, a resettable fuse that can significantly enhance the reliability of a USB application from both catastrophic and shutdown failures from onsemi. It is designed to buffer the load device from the excessive input voltage, which can damage sensitive...
Expand 14 Click is a compact add-on board that contains a multi-port I/O expander. This board features the CAT9555, a CMOS device that provides 16-bit parallel input/output port expansion from onsemi. The CAT9555 contains two 8-bit configuration ports (input or output), input, output, and polarity inversion registers, alongside an I2C-compatible serial...
Expand 16 Click is a compact add-on board with a multi-port I/O expander. This board features the FXL6408, a fully configurable 8-bit GPIO expander from onsemi. It brings eight independently configurable input/output ports, with a 6mA output drive, when configured in the output mode. When configured in Input Mode, the FXL6408 monitors the input ports for...
H-Bridge Driver 2 Click is a compact add-on board that contains an H-bridge gate driver, also known as a full-bridge pre-driver. This board features the NCV7535, a monolithic H−bridge pre-driver for a DC motor with an enhanced feature set, useful in automotive systems from onsemi. The gate driver channels are independently controlled by a 24-bit SPI...
Loading
Load more
Loading