Filter Product By
Slide and select filter/s
Filtered by
Categories
Mikroe has collaborated closely with Microchip to offer you a broad portfolio of products from this vendor, which will help you reducing development effort and accelerate time to market. As a 3rd party tool provider we strive to promote partners newest theologies and products, by offering them to the broad market.
DC Motor 8 click is a DC motor driver. It can drive simple DC motors with brushes, providing them with a significant amount of current and voltage up to 40V. The click has one control input, that uses the PWM signal from the host MCU. It uses the half-bridge topology to regulate the speed of the motor rotation, employs advanced dead-time circuitry that...
DIGI POT 5 click is a digitally controlled quad potentiometer, with the resistance of 10KΩ. It has an 8bit wiper step resolution, which allows the wiper to take 257 different discrete positions (across 256 internal resistors). The digital wiper position can be controlled via the SPI interface. DIGI POT 5 click features a durable EEPROM non-volatile (NV)...
DIGI POT 6 Click is a compact add-on board used as a digitally controlled potentiometer. This board features the MCP41HV51, 8-bit dual power rails digital potentiometer with SPI serial interface and volatile memory from Microchip. The MCP41HV51 has a wide operating voltage range, analog from 10 to 36V and digital from 2.7 to 5.5V or implemented as...
DIGI POT Click is a compact add-on board with a digitally controlled potentiometer. This board features the MCP4161, an 8-bit single SPI digital POT with non-volatile memory from Microchip. It is designed to operate as a variable resistor for analog signals with the voltage range of single-supply operation. The MCP4161 in 8-bit resistor network resolution...
The Digital Potentiometer Board includes a SPI Interfaced single-channel digital potentiometer MCP41010. The board enables you to set potentiometer values from 0 to 10 kΩ. It comes with many simple and ready-to-use examples.
DigiVref click is a very precise voltage reference Click board™, which allows one of four different voltage values to be selected over the SPI interface. Once the selection is done, the voltage reference stays fixed, even when the SPI interface is completely disconnected. The voltage reference is buffered by an operational amplifier, and thus it is very...
DMX Click is a device used to establish communication between the MCU and equipment that uses the DMX512-A communication protocol. Unlike many similar solutions on the market, this unique device allows using the common UART data format, which is converted to an appropriate DMX512 format by the powerful PIC18F26K42 MCU from Microchip. This MCU has an...
dsPIC-Ready1 Board dsPIC-Ready1 Board provides the best solution for fast and simple development of 40-pin dsPIC30F microcontroller applications (dsPIC30F3011 and dsPIC30F4011). It includes connectors for connecting the dsPICprog with mikroICD in-system stand-alone programmer. These connectors enable you to program microcontrollers without any other...
dsPIC-Ready2 Board dsPIC-Ready2 Board provides the best solution for fast and simple development of 40-pin dsPIC30F microcontroller applications (dsPIC30F3014 and dsPIC30F4013). It includes connectors for connecting the dsPICprog with mikroICD in-system stand-alone programmer. These connectors enable you to program microcontrollers without any other...
dsPIC-Ready3 Board dsPIC-Ready3 Board is the best solution for fast and simple development of 28-pin dsPIC30F microcontroller applications (dsPIC30F2010, dsPIC30F3010, dsPIC30F4012, dsPIC30F2012, dsPIC30F3013 etc.). It includes connectors for connecting the dsPICprog with mikroICD in-system stand-alone programmer. These connectors enable you to program...
dsPIC-Ready4 Board dsPIC-Ready4 Board is the best solution for fast and simple development of 28-pin dsPIC30F microcontroller applications (dsPIC30F1010, dsPIC30F2020 etc.). It includes connectors for connecting the dsPICprog with mikroICD in-system stand-alone programmer. These connectors enable you to program microcontrollers without any other...
DTMF Decoder Click is a compact add-on board that contains an integrated DTMF receiver with enhanced sensitivity. This board features the MT8870D, a complete DTMF receiver integrating the band-split filter and digital decoder functions from Microchip Technology. It offers low power consumption and high performance and uses digital counting techniques to...
Dual EE Click contains two AT24CM02 EEPROM ICs onboard which gives total of 4MB of memory. Each memory IC can be addressed through the I2C interface with the transfer speed of 400KHz. This Click board™ offers any kind of temporary or permanent data storage for various. embedded electronic devices, as well as simple data logging or even storing various...
The Easy24-33 v6 development system supports 14-, 18-, 20- and 28-pin PIC24 and dsPIC33 microcontrollers from Microchip. It comes with a PIC24F16KA102. The system features a USB 2.0 programmer with mikroICD and many peripheral modules such as Touch Sense, Serial RAM, EEPROM, etc.
The Easy8051 v6 is compatible with 14-, 16-, 20-, 28-, 40-pin PLCC44 and PLCC32 MCUs. It comes with an AT89S8253. The board has a USB 2.0 programmer and many peripherals such port expander, MENU and 4x4 keypads etc. Note: the COG display is not included in the package; instead the package includes an LCD 2x16 display.
EasyAVR PRO v8 is packed in the protective box along with the relevant documentation.This box is very resistant to all kinds of damage and shock. The package contains: Damage resistant protective box EasyAVR PRO v8 board SiBRAIN and Display board flyers Adapter - USB Micro Female to USB Type-C Male Adapter - USB-C Female to USB-A Male USB-C...
EasyAVR PRO v8 over USB-C is a full-featured development board for high pin-count 8,16-bit AVR® microntrollers. It contains many on-board modules necessary for device development, including multimedia, Ethernet, USB, and other.
Top selling AVR Development Board for over 64 Atmel AVR MCUs in DIP packaging. It features USB 2.0 programmer and many essential and usefull modules necessary in development. Board comes with ATMEGA32. Buy now The Best AVR® Board. Ever. Four connectors for each port Amazing Connectivity EasyAVR™ v7 is all about connectivity. Having four...
EasyAVR v8 EasyAVR v8 is packed in the protective box along with the relevant documentation. The package contains: Damage resistant protective box EasyAVR v8 board Adapter - USB-C Female to USB-A Male Adapter - USB Micro Female to USB-C Male USB cable Board Schematic User Manual CODEGRIP Suite Quick Start Guide MCU PIC18F47K42 and 8MHz...
The EasyLV-18F v6 development system supports 40-, 28- and 20-pin PIC18J and PIC18K microcontroller families from Microchip. It comes with a PIC18F45K20. The system features a USB 2.0 programmer with mikroICD and many peripheral modules such as Serial RAM, EEPROM, COG Display, etc.
Support for three different architectures: dsPIC33, PIC24 and PIC32 in a single development board. It contains many on-board modules, including multimedia, Ethernet, USB, CAN and other. On-board mikroProg™ programmer and debugger supports 101 microcontrollers via MCU cards. Buy now Note: MCU and click boards are not included in the package. One...
EasyPIC Fusion v7 Empty MCUcard ETH 100pin TQFP PT. Card is not populated with components. pin distance 100mil.
EasyPIC Fusion v7 Empty MCUcard ETH 144pin LQFP PL is not populated with components.
Loading
Load more
Loading
