Filter Product By
Slide and select filter/s
Filtered by
UV 3 click is an advanced ultraviolet (UV) light sensor with I2C protocol interface. The click carries VEML6070 UVA light sensor designed by the CMOS process. UV 3 click runs on either 3.3V or 5V power supply.
The great thing about SpeakUp click is that it works as a standalone device because it has an STM32 ARM® Cortex®-M4 MCU on it. To use it as a light switch, or as an electrical switch for any other appliance, you just have to combine it with a relay click. It will take 15 minutes to set it all up. It's ridiculously easy.
Touchpad 4 Click is a compact add-on board that easily integrates projected capacitive touch into user's applications. This board features the IQS7211A, a tiny capacitive touch controller from Azoteq. A low-power dedicated wake-up touch controller launches a complete touchscreen sensing solution with a 25.4 x 29mm trackpad dimension, best-in-class...
STSPIN820 click is a stepper motor driver with the PWM current control, selectable microstepping up to 256 microsteps, and a wide voltage range. It is based on the STSPIN820, a stepper motor driver from STSPIN8 series. Designed to be a bullet-proof solution for the new wave of demanding industrial applications, it integrates two full-bridges with low ON...
I2C MUX Click is an quad bidirectional translating I2C and SMBus switch with reset function, intended for applications with I2C slave address conflicts (multiple, identical temp sensors). It features a quad bidirectional translating switch controlled via the I2C bus, labeled as TCA9546A from Texas Instruments. Click has three address jumpers, allowing up...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
DC Motor 17 Click is a compact add-on board that contains a brushed DC motor driver. This board features the TC78H660FTG, a dual H Bridge driver for one or two brushed motors that incorporate a DMOS output transistor with low on-resistance from Toshiba Semiconductor. This IC is a PWM controlled constant-current drive with supply voltages from 2.5V to 16V...
CODEGRIP for PIC is a fast USB-C and WiFi programmer and hardware debugger. It supports PIC10, PIC12, PIC16, PIC18, dsPIC30/33, PIC24, and PIC32 devices in a single programmer. This is a version without a WiFi module assembled.
Charger 19 Click is a compact add-on board that contains a battery charger. This board features the nPM1100, an integrated power management IC from Nordic Semiconductor. It has a highly efficient DC/DC buck regulator with automatic selection between hysteretic and PWM modes. The nPM1100 has automatic USB port detection and features discharge current...
Angle 3 click carries the AK7451, a magnetic rotational angle sensor. The click is designed to run on a 5V power supply. It communicates with the target microcontroller over SPI interface, with additional functionality provided by the INT pin on the mikroBUS™ line.
Plug&Trust Click is a compact add-on board that contains a ready-to-use IoT secure element solution. This board features the SE050C secure element IC NXP, which provides a root of trust at the IC level, and it gives an IoT system state-of-the-art, edge-to-cloud security capability. The SE050C allows for securely storing and provisioning credentials...
TFT Proto 4.3" carries a 480x272 ATO43B35 TFT screen covered with a 4-wire resistive touchscreen panel. To drive the 262k-color display, there's an SSD1963 graphic controller with a 8/9/16/24-bit MCU interface that includes a deep-sleep power saving.
IR Reflect Click is a compact add-on board that adds reflective photo interrupter ability to any application. This board features the GP2S700HCP, a compact package, phototransistor output, and a reflective photo-interrupter from Sharp Microelectronics. The emitter and detector face the same direction in a molding that provides non-contact sensing that...
Fusion for PIC32 v8 is packed in the protective box along with the relevant documentation.This box is very resistant to all kinds of damage and shock. The package contains: Damage resistant protective box Fusion for PIC32 v8 board MCU and Display board flyers Adapter - USB-C Female to USB-A Male Adapter - USB Micro Female to USB-C Male...
Convert TSSOP-SSOP 14 pins (300 mil wide) package to DIP 14 pins.
Convert TSSOP-SSOP 16 pins (300 mil wide) package to DIP 16 pins.
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
Silent Step Click is the complete integrated bipolar step motor driver solution, rich with many features that allow extremely smooth and silent operation of the connected motor while being able to provide up to 2.5A peak motor current and withstand up to 46V supply voltage. The specialized TMC5130 IC driver from Analog Devices far exceeds the capabilities...
The EasyPIC6 PROTO Board is a high quality PCB prototype board. It solves your prototype problems by offering a complete, cost-effective solution. Connect your EasyPIC6 development board to this board via an IDC10 connector.
DIGI POT 8 Click is a compact add-on board used as a digitally controlled potentiometer. This board features the AD5206, 6-channel 256-position digitally controlled variable resistor device from Analog Devices. Each channel of the AD5206 contains a fixed resistor with a wiper contact that taps the fixed resistor value of 100kΩ at a point determined by a...
Single Wire CAN Click is a compact add-on board that contains an IC for a single wire data link capable of operating with various protocols such as the Controller Area Network (CAN). This board features the NCV7356D1R2G, Single Wire CAN transceiver from onsemi, which operates from a supply voltage from 5V to 27V with bus speed up to 40 kbps. It supports...
CAN FD 5 Click is a compact add-on board that contains CAN transceiver that supports both CAN and CAN FD protocols. This board features the UJA1162A, a ‘self-supplied’ high-speed CAN transceiver integrating an ISO 11898-2:2016 and SAE J2284-1 to SAE J2284-5 compliant CAN transceiver with Sleep Mode from NXP Semiconductors. It features an under-voltage...
If you need motor contol and DSP processing then this kit with mikromedia for dsPIC33 is a solution for you.
Loading
Load more
Loading
