Filter Product By
Slide and select filter/s
Filtered by
The IrDA PROTO Board allows you to connect your prototype board to IrDA wireless network by using the MCP2155 driver and TFDU4101 diode. As soon as you establish connection, data can be sent/received via IrDA wireless network.
Brushless 3 click carries the DRV10983, a three-phase sensorless motor driver with integrated power MOSFETs. When an external power supply is applied, you can drive a brushless DC motor through the PWM pin, AN pin or I2C interface. It communicates with the target microcontroller over I2C interface, with the additional functionality provided by the...
Note: This product is obsolete. EasyPIC Fusion v7 standard 124-pin TQFP card with PIC32MZ2048ECH MCU
The Ultrasonic 2 click is an ultrasonic range detection Click board™, capable of detecting both near-field and far-field objects. It is equipped with the PGA460, a highly-integrated system-on-chip (SoC), based on SONAR principle. This SoC consists of a low-noise analog front end (AFE) with a programmable time-varying gain stage, a digital signal processor...
LIN HALL Click is a compact add-on board representing a linear Hall-effect sensing solution. This board features the MLX90242, a linear Hall-effect sensor with built-in active error correction circuitry from Melexis Technologies. The MLX90242 outputs a signal proportional to the flux density of a magnetic field, further processed by the MCP3201, a 12-bit...
LSM303AGR click is a magnetometer and accelerometer device, capable of sensing both the magnetic and gravitational field along three orthogonal axes. It uses the LSM303AGR from STMicroelectronics, an integrated MEMS IC with plenty of features that allow accurate and reliable sensing, even in presence of foreign objects made of iron and similar materials...
The GNSS Active External Antenna is a unique multi-band type of antenna coming from u-Blox that is perfect selection for high precision GNSS applications, which require highly accurate location abilities such as RTK. The ANN-MB-00 is a multi-band (L1, L2/E5b/B2I) active GNSS antenna with 5 m cable and SMA connector. Antenna supports GPS, GLONASS, Galileo...
PS/2 Connector Board is accessory board used to connect PS/2 devices to a prototype device. There is a PS/2 connector provided on the board. It enables PS/2 communication.
Altitude 2 Click is a high-resolution barometric pressure sensor add-on Click board™. It carries the MS5607, a barometric pressure sensor IC with the stainless steel cap, produced by TE Connectivity. This sensor provides very accurate measurements of temperature and atmospheric pressure, which can be used to calculate the altitude with a very high...
10-pin 0.05" ARM Cortex Debug Adapter comes with flat cable with IDC 2x5 0.05" pitch connectors The standardized connector ensures seamless integration with the CODEGRIP - World's first programmer/debugger over WiFi and USB-C, while its compact design enhances convenience for swift programming and debugging tasks.
Relay 5 Click is a compact add-on board with general-purpose I2C-controlled relays that any host MCU can control. This board features three J1031C3VDC.15S, a high-current single-pole double-throw (SPDT) signal relays controlled by the PCA9538A, a low-voltage 8-bit I/O port expander from NXP Semiconductors. Highly sensitive, the J1031C3VDC.15S offers a low...
Tact Switch 4.5x4.5mm TH (10pcs)
The Peltier Click is a Click board™ which utilizes the SPV1050, an ultralow power energy harvester and battery charger from STMicroelectronics. The Peltier click can charge lithium battery using thermoelectric energy harvesting device (TEG). A TEG converts heat directly into electrical energy according to the Seebeck effect. It can be used for a variety...
3Pin Screw Terminal Connector (OSTVN03A150) is a 3-position 2.54mm pitch PCB terminal block from On-Shore Technology that provides connections for high current conductors. It can withstand current and voltage ratings up to 6A and 125VAC, ensuring reliability in power delivery applications. Based on their compact design and dimensions, 6.5x8.02x8.5...
Opto 2 click is a galvanic isolator Click board™, used to provide an optical isolation of sensitive microcontroller (MCU) pins, when operated by external signals. TLP2770 opto-isolation elements (optocouplers) can be driven with a very low current, down to 1.3mA (min). A choice of high-speed optocouplers allows Opto 2 click to be used on communication...
mikroLab for PIC is the essential toolkit for 8-bit PIC development for low pin-count chips. EasyPIC v7 – perhaps MikroElektronika’s most famous board – supports more than 380 PIC MCUs.
USB-C Sink Click is a compact add-on board that contains a standalone autonomous USB power delivery controller. This board features the STUSB4500, a USB-C sink-only controller compatible with Power-Delivery (PD) from STMicroelectronics. It supports dead battery mode to allow a system to be powered from an external source directly, establishes a valid...
Diff Press Click is an accurate pressure sensor Click board™ capable of measuring differential pressure. This Click board™ utilizes a very precise differential pressure sensor from NXP, labeled as MPXV7007DP. This piezo-resistive transducer is an advanced monolithic pressure sensor, combining advanced MEMS manufacturing technologies with on-chip signal...
The IrDA-To-PC Board is used to enable a PC to use IrDA communication. The board features MCP2120 along with TFDU4101 diode and other electronics required for connecting a PC to other IrDA devices. NOTE: This product has been moved to Legacy status, meaning it is no longer in active production or supported with updates. For continued use in similar...
Thermo 2 Click is a compact add-on board that accurately measures temperature. This board features the DS1825, a programmable resolution 1-wire digital thermostat from Analog Devices. The DS1825 digital thermometer provides 9 to 12-bit centigrade temperature measurements alongside the alarm function with NV user-programmable upper and lower trigger...
9DOF 2 Click is a compact add-on board for applications which require lowest power motion tracking and magnetometer functionality. This board features the ICM-20948 a 9-axis MotionTracking™ sensor from TDK Invensense, which consist of two sensors combined into one package for universal 9DOF solution. In this package we have 3-axis gyroscope, a 3-axis...
mikroProg for CEC is a fast programmer and hardware debugger. Smart engineering allows mikroProg to support the CEC cryptographic engine with secure firmware updating. Outstanding performance, easy operation, elegant design and low price are its top features. It is supported in MikroElektronika ARM compilers (mikroC, mikroBasic, and mikroPascal). This...
NB IoT 2 Click is a compact add-on board that contains a compact LTE Cat NB2 module with ultra-low power consumption. This board features the BC66-NA, a high-performance, multi-band LTE Cat NB2 module with extremely low power consumption from Quectel Wireless Solutions. It provides a flexible and scalable platform for migrating from GSM/GPRS to NB-IoT...
IrThermo 2 Click is a compact add-on board that allows contactless measurement of the object’s temperature. This board features the TMP007, an infrared thermopile sensor with an integrated Math Engine from Texas Instruments. It is a low-power, fully integrated microelectromechanical system (MEMS) that absorbs passive infrared energy from an object at...
Loading
Load more
Loading
