Filter Product By
Slide and select filter/s
Filtered by
Charger 24 Click is a compact add-on board designed to provide USB-C charging for single-cell lithium-ion or lithium-polymer batteries in portable applications. It is based on the MAX77751, a highly integrated autonomous charger IC from Analog Devices with built-in USB Type-C detection and power management features. The board features a synchronous...
Empty 64- and 100-pin PIC32 MCU Cards have a very good contact with the board via a two-line connector.
Not a programming expert, but you have the talent to build a great user interface? Don't worry! Visual TFT will do the hard job for you. You just focus on the design of you TFT GUIs, and the software will handle the rest.
The essential development kit for all your graphic interface projects Open the box full of wonders. Start development right away, everything you could need is there. It’s the perfect toolbox - the mikromedia workStation v7 is the best development environment for mikromedia boards – your stepping stone. The Visual TFT software and compiler license will...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
Hall Current 13 Click is a compact add-on board that provides economical and precise AC or DC current sensing solutions. This board features the TMCS1107-Q1, a galvanically isolated Hall-effect current sensor capable of DC or AC current measurement with high accuracy, excellent linearity, and temperature stability from Texas Instruments. It enables the...
Rec&Play 2 Click is a compact add-on board for voice recording and playback applications. It is based on the ISD1616B, a single-message voice record and playback IC from Nuvoton. The board features an on-chip oscillator, a microphone preamplifier with Automatic Gain Control (AGC), an omnidirectional microphone, and a speaker driver for high-quality...
Buck 13 Click is a high-efficiency step-down converter which provides a highly regulated output voltage derived from the connected power source, rated from 4.5V to 5.5V. The regulated output voltage is 3.3V, the most common choise for various embeded applications. Buck 13 click is based around an integrated DC-DC converter, labeled as MPM3530. Due to its...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
for PIC32MZ CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 3 for PIC32MZ CAPACITIVE is not limited to multimedia-based applications only. USB, digital motion sensor, battery charging functionality, SD card reader and much more expands its use beyond the...
Stepper 17 Click is a compact add-on board that contains a bipolar stepper motor driver. This board features the TB67S539FTG, a two-phase bipolar stepping motor driver using a PWM chopper from Toshiba Semiconductor. It supports a PWM constant-current control drive without a current sense resistor for motor-current detection and full-step to 1/32 steps...
for PIC32MZ CAPACITIVE FPI with bezel Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 4 for PIC32MZ CAPACITIVE FPI with bezel is not limited to multimedia-based applications only. USB, digital motion sensor, battery charging functionality, SD card reader and much...
Fusion for ARM v8 is a development board for ARM architecture devices. It contains many on-board modules necessary for device development, including multimedia, Ethernet, USB, and other.
DIGI POT 14 Click is a compact add-on board that contains a digitally controlled potentiometer. This board features the TPL0102, a dual-channel digital potentiometer with non-volatile memory from Texas Instruments. It is a 100K resistance end-to-end potentiometer with a 256-position resolution, where the wiper position can be stored in EEPROM. It can...
Gyro 9 Click is a compact add-on board that contains a high-performance gyroscope. This board features the A3G4250D, a MEMS motion sensor from STMicroelectronics. It is a low-power 3-axes digital output gyroscope that provides unprecedented stability at zero rate level and sensitivity over temperature and time and is equipped with an embedded temperature...
Light 3 Click is a compact add-on board for precise ambient light measurement in automotive applications. This board features the OPT4003-Q1, an automotive-grade digital ambient light sensor from Texas Instruments. This digital ambient light sensor excels in detecting both visible and near-infrared light with high accuracy, thanks to its dual-channel...
Inclinometer 3 Click is a compact add-on board for precise tilt and leveling measurement applications. This board features the SCL3400-D01, a two-axis inclinometer sensor from Murata, leveraging advanced capacitive 3D-MEMS technology. It features a high-performance mixed-signal ASIC with a flexible SPI digital interface housed in a robust 12-pin...
EasyMx PRO v7 for Tiva C Series Empty MCU card for 64-pin TQFP TM4C123 series. Card is not populated with components. Pin distance 100mil.
Tilt 3 Click is a compact add-on board used for measuring the tilt in multiple axes in relation to an absolute level plane. This board features the DSBA1P, a tilt sensor switch that breaks the circuit when tilted to an angle from ±30° to ±60° from NKK Switches. The DSBA1P is a non-contact switch with an embedded photo-interrupter that ensures high...
for PIC CAPACITIVE FPI with frame Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 4 for PIC CAPACITIVE FPI with frame is not limited to multimedia-based applications only. USB, digital motion sensor, battery charging functionality, SD card reader and much more...
Magneto 11 Click is a compact add-on board that contains an accurate and reliable magnetic sensing device. This board features the AS5510, a linear hall sensor with 10-bit resolution, and an I2C interface from ams AG. It can measure the absolute position of lateral movement of a simple 2-pole magnet. A lateral stroke of 0.5mm ~ 2mm can be measured with...
Loading
Load more
Loading
