Filter Product By
Slide and select filter/s
Filtered by
Buck 3 click is a very advanced synchronous step-down (buck) converter, which is designed to deliver noise and ripple-free voltage to highly sensitive applications, such as FPGA and high-performance DSP platforms. The onboard step-down converter IC integrates low RDSON MOSFETs, that allow high efficiency, and thus high current on the output - up to 8A....
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
Index Counter Click is a simple prototyping high precision Hall-Effect switch solution with direction detection. This board is hosting TLE4966K an integrated circuit dual Hall-effect sensor from Infineon. The sensor is designed specifically for highly accurate applications which use a rotating pole wheel since offers high sensitivity and high stability of...
Stepper 18 Click is a compact add-on board that contains a microstepping stepper motor driver. This board features the DRV8426, a stepper motor driver for industrial and consumer applications from Texas Instruments. It is fully integrated with two N-channel power MOSFET H-bridge drivers, a microstepping indexer, and integrated current sensing capable of...
6-pin Needle Cable is a compact programming cable made from high-quality materials for longevity and easy portability with a tiny square footprint, similar to a 0805 resistor. Designed for quick programming and debugging, it features a 6-pin 0.1″ pitch ribbon connector and is hand-held or temporarily fixable. Use the 6-pin Needle Cable to extend the...
ISM 5 Click is a compact add-on board designed for seamless integration into a wide range of applications requiring efficient communication in the Sub-GHz 868MHz frequency band. This board features the Si4461, a high-performance, low-current transceiver from Silicon Labs known for its robust operation in time division duplexing (TDD) mode, enabling...
Pressure 23 Click - 07BA is a compact add-on board for accurate and reliable absolute pressure and temperature measurements in harsh environments. This board features the MS5849-07BA, an ultra-compact, chlorine-resistant sensor from TE Connectivity that delivers 24-bit resolution data via I2C or SPI interfaces. It operates within pressure ranges of 0.4 to...
Empty PSoC MCU Cardsthat enable you to solder different PSoC microcontrollers and other electronic components you need on them.
1-Wire Switch Click is a compact add-on board that allows you to switch a device remotely using a 1-wire signal. This board features the DS2413, a dual-channel programmable I/O 1-Wire switch from Analog Devices. Communication and operation of this Click board™ are performed with the single 1-Wire serial interface, with the possibility of selecting signals...
EasyMx PRO v7 for Tiva C Series Empty MCU card for 100-pin TQFP TM4C123 series. Card is not populated with components. Pin distance 100mil.
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
for Kinetis CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 5 for Kinetis CAPACITIVE is not limited to multimedia-based applications only. USB, Ethernet, WiFi and RF connectivity options, digital motion sensor, battery charging functionality, piezo-buzzer,...
for PIC CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 4 for PIC CAPACITIVE is not limited to multimedia-based applications only. USB, digital motion sensor, battery charging functionality, SD card reader and much more expands its use beyond the...
Charger 16 Click is a compact add-on board that represents a single-cell battery charger. This board features the LT1571, a constant-current/constant-voltage battery charger with preset voltage and termination flag from Analog Devices. Powering up from an external power supply rated up to 20V, this Click board™ has an onboard current sense resistor which...
Barometer 6 Click is a compact add-on board used to measure air pressure in a specific environment. This board features the 2SMPB-02E, a high-accuracy digital barometric air pressure sensor with low current consumption from Omron Electronics. The 2SMPB-02E has a calibration parameter for broader pressure and temperature range, features a MEMS chip for...
Brushless 27 Click is a compact add-on board that controls DC brushless motors with any MCU. This board features the TMC6300, a power driver for BLDC/PMSM motors from Analog Devices. It is a highly efficient low voltage, zero standby driver for 3-phase BLDC/PMSM motors with up to 2A peak current. The triple half-bridge of this driver separates the HS and...
Build your own programmable timer relays using AVR-Ready, Keypad 4x4 board with EasyPull, RTC, Relay 4 and LCD 2x16 character display with adapter. Just load the demonstration project code and your device is ready to control 4 separate relays.
mikroLab for FT90x is a complete – and only – solution for developing with FTDI Chip’s FT90x line of MCUs. The kit contains an EasyFT90x v7 board, a mikroC for FT90x compiler license, additional accessories, and a free license for Visual TFT (valued at $99).
Angle 8 Click is a compact add-on board that detects the absolute angular position of a permanent magnet. This board features the MA782GGU, a low-power angle sensor with integrated wake-up angle detection from Monolithic Power Systems. With its power cycling ability, the MA782GGU can be optimized for applications that require low average power. It...
Vibration ERM Motor 9K RPM 3V (VC1026B002F) represents the Eccentric Rotating Mass vibration motor (ERM), also known as a pager DC motor, with an offset (non-symmetric) mass attached to the shaft specially designed by Vybronics. This coin-sized vibration motor comes with a metallic case circular shape of 10mm diameter and draws a maximum of 85mA while...
This one is for all NECTO Studio IDE users and people who love wearing modern designs. This T-shirt is in blue color with the "Ideal way of coding" sign on the front and the MIKROE logo on the left sleeve. FEMALE SIZES CHART Size S M L XL XXL Lenght(cm) 63 65 67 68 70 Width(cm) 43 45 48 50 53 MALE...
Step Down 8 Click is a compact add-on board that converts higher voltages into a lower voltage level. This board features the MAX25232, a mini buck converter from Analog Devices. It is designed to deliver up to 3A with 3.5V to 36V input voltages while using only 3.5μA quiescent current at no load. The MAX25232 integrates high-side and low-side switches...
MICRF TX Click is a compact add-on board designed as a powerful RF transmitter for data transmission over the 315MHz frequency band. This board features the MICRF112, a high-performance RF transmitter IC from Microchip, renowned for its efficiency in operation. This Click board™ stands out for its ease of use, requiring only a simple crystal oscillator to...
Tamper click is equipped with SDS001, a low profile side-actuated detect switch, made by C&K company. This is a high-quality, low-current detection switch, which is designed in a form of a push button. The switch itself is very small - only 2mm of switch overtravel length, which coupled with its low actuation force, makes it ideal for using it as a...
Loading
Load more
Loading
