Filter Product By
Slide and select filter/s
Filtered by
DAC 11 Click is a compact add-on board that contains a highly accurate digital-to-analog converter. This board features the DAC128S085, a general-purpose OCTAL 12-bit analog voltage-output DAC from Texas Instruments. It uses both logic voltage levels from the mikroBUS™ socket with a maximum power consumption of 4.85mW at 5V. The on-chip output amplifiers...
Barometer 7 Click is a compact add-on board used to measure air pressure in a specific environment. This board features the KP264XTMA1, a high-accuracy digital barometric air pressure sensor based on a capacitive principle from Infineon Technologies. The KP264XTMA1 is surface micromachined with a monolithic integrated signal conditioning circuit...
Flash 9 Click is a compact add-on board that contains a highly reliable memory solution. This board features the W25Q02JV, an SPI configurable serial Flash memory solution from Winbond Electronics. It represents a four 512Mb stack die supporting linear addressing for the full 2Gb memory address range, offering flexibility and performance well beyond...
USB 2.0 Micro Female to USB Type C Male Adapter represents a high-speed type C connector that converts the USB-C 2.0 micro head data into the ordinary USB 2.0 data cable. It has a data transfer rate of up to 480Mbps and supports high-power charging and quick data transfer alongside a reversible plug orientation and cable direction. Based on its compact...
Piezo Buzzer (EPT-14A4005P) is an electronic device used to produce a tone, alarm, or sound from Sanco Electronic. This TH buzzer has a resonant frequency of 4000Hz, draws a maximum current of 2mA, and is an excellent choice for various applications including alarms and warning systems in automobiles and consumer electronics, and much more, thanks to its...
NeoMesh Click - 868MHz is a compact add-on board with a low-power, long-range transceiver, ideal for Mesh wireless networking. This board features the NC1000C-8, a wireless Mesh network module from NeoCortec. With an additional antenna that MIKROE offers connected to the module’s u.Fl connector, you can create a fully functional wireless Mesh network node...
Adapter - USB-C Female to USB-B Male represents a high-speed type C connector that converts the USB-C head data into the USB 2.0 Type B data. This adapter offers data transfer speeds of up to 480Mbps between connected devices and comes with a built-in 56kΩ pull-up resistor for safer and more reliable quality. Its compact design and dimensions provide an...
EasyAVR v8 EasyAVR v8 is packed in the protective box along with the relevant documentation. The package contains: Damage resistant protective box EasyAVR v8 board Adapter - USB-C Female to USB-A Male Adapter - USB Micro Female to USB-C Male USB cable Board Schematic User Manual CODEGRIP Suite Quick Start Guide MCU PIC18F47K42 and 8MHz...
Current 11 Click is a compact add-on board for industrial and commercial current-sensing applications. This board features the ACS37600K (ACS37600KOKATN-006B5-C), a programmable linear Hall-effect sensor IC from Allegro Microsystems. This sensor features a chopper-stabilized Hall-effect front-end for precise magnetic flux detection, with a sensitivity of...
LV-24-33 v6 80-pin TQFP 2 MCU Card Empty PCB
This Pedometer consists of a mikromedia for STM32-M4, a mikromedia Proto shield and LiPo battery. Let's measure how far you walked with this Let's make. A pedometer is a portable device that counts each step a person takes.
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
The Step Down 2 click is a Click board™ equipped with the L6986HTR, a synchronous step-down switching regulator with operating input voltages from 4V to 38V and output voltage adjustability ranges from 0.85 V to VIN. Because of the main possibilities its features offer, the Step Down 2 click is ideally used for programmable logic controllers (PLCs),...
TFT Color Display with Touch Screen (4.3") and decorative cover glass (black bezel) is a color active matrix thin film transistor(TFT) liquid crystal display (LCD).
pH Click is a compact add-on board that provides an opportunity for the user to read pH with the same accuracy and capabilities as with some other expensive solutions. This board features the pH EZO™, a 6th generation embedded pH circuit that offers the highest level of stability and accuracy from AtlasScientific. With an easy to use data protocol, simple...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
I2C Isolator 6 Click is a compact add-on board that offers completely isolated bidirectional communication. This board features the ADUM2250, a two-channel, 5kVRMS I2C digital isolator from Analog Devices. The ADUM2250 provides two bidirectional channels, supporting a completely isolated I2C interface that eliminates the need for splitting I2C signals...
LR 15 Click is a compact add-on board designed for ultra-low-power long-range communication in IoT applications. It is based on the Wio-E5-LE, a LoRaWAN® module from Seeed Studio, featuring the STM32WLE5JC SoC and SX126X LoRa® chip for high-performance and energy-efficient operation. This board supports LoRa® and (G)FSK modulation modes, with adjustable...
for STM32F7 CAPACITIVE FPI with frame Rapid development of multimedia and gui-centric applications
for PIC CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 3 for PIC CAPACITIVE is not limited to multimedia-based applications only. USB, digital motion sensor, battery charging functionality, SD card reader and much more expands its use beyond the...
TFmini Click Bundle: This bundle gives you everything you need to take high-accuracy distance measurements. It allows users to combine TFmini S LiDAR Sensor, a high-accuracy ToF (Time of Flight) LiDAR sensing solution from Benewake, with TFmini Click to measure an object's distance.
Loading
Load more
Loading
