Filter Product By
Slide and select filter/s
Filtered by
TFT Board 3 Resistive is a 3.5" display board which features the standardized 2x20-pin display connector. The display board also integrates a resistive touch panel. The TFT display module supports up to 24-bit pixel format (RGB: 888) and resolution of 320 x 240 pixels. It features an excellent contrast ratio and uniform brightness. TFT Board 3 Resistive,...
AWS IoT Click is a compact add-on board that allows users to easily connected to AWS IoT services and securely interact with cloud applications and other devices. This board features the ESP32-C3-MINI-1-N4-A, a small 2.4GHz WiFi (802.11 b/g/n) and Bluetooth® 5 module from Espressif Systems that use ESP32C3 series of SoC RISCV single-core microprocessor...
Click Shield for Teensy 4.0 Unlock the full potential of your Teensy 4.0 with the Click Shield for Teensy 4.0! Supercharge your Teensy 4.0 board by adding mikroBUS™ sockets, giving you instant access to a vast selection of Click boards™. Expand your project's capabilities and explore endless innovation opportunities with just one host board.
MCP16331 INV click works as a buck-boost voltage regulator, a switching regulator topology that combines principles of the buck conversion (step-down) and the boost conversion (step-up). A buck converter outputs voltage that is smaller than the input voltage (steps down the input voltage). A boost converter outputs voltage that is greater than the input...
MRAM 2 Click is a compact add-on board for applications that must store and retrieve data and programs quickly using a small number of pins. This board features the MR10Q010, 1Mb Quad Output High-Speed Serial SPI MRAM memory solution from Everspin Technologies. It operates in both standard, single SPI and High-speed QUAD SPI mode with a clock rate up to...
BATT-MAN 3 Click is a compact add-on board representing an advanced battery management solution. This board features the ADP5350, a power management IC with inductive boost LED, and three LDO regulators from Analog Devices. This I2C programmable board supports USB optimized for USB voltage input. It combines one high-performance buck regulator for single...
for PIC32MZ CAPACITIVE FPI with bezel Rapid development of multimedia and gui-centric applications
SolidSwitch 2 Click is a compact add-on board that contains a load switching device. This board features the L9026, an automotive eight-channel relay driver from STMicroelectronics. The L9026 incorporates two high-side drivers and six configurable high-side/low-side drivers driven by an SPI interface or by two dedicated parallel inputs. Operating from an...
RTC 21 Click is a compact add-on board that accurately keeps the time of the day. This board features the PT7C4311, an I2C-configurable real-time clock module with programmable square-wave output from Diodes Incorporated. The PT7C4311 includes time and calendar functions providing various information such as hour, minute, second, day, date, month, year,...
RTC 22 Click is a compact add-on board for accurate timekeeping and power management in low-power applications. This board features the AM1805AQ, an ultra-low power real-time clock IC from Ambiq, using the innovative SPOT® CMOS platform for minimal energy consumption. The board features on-chip oscillators, battery backup with a rechargeable micro-energy...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
Brushless 17 Click is a compact add-on board suitable for controlling brushless DC (BLDC) motors with any MCU. This board features the L6229Q, DMOS fully integrated three-phase BLDC motor driver with overcurrent protection from STMicroelectronics. This motor driver combines isolated DMOS power transistors with CMOS and bipolar circuits on the same chip,...
I2C Isolator 4 Click is a compact add-on board that provides fully isolated bidirectional communication. This board features the MAX14937, a two-channel, 5kVRMS I2C digital isolator from Analog Devices. The MAX14937 provides two bidirectional, open-drain channels for applications that require data to be transmitted in both directions on the same line. It...
Smart programmable touch display, packed with features. Mikromedia can be used as a powerful programmable dashboard control panel for both hobby projects, but also for the entire systems. Based on the powerful FT900 MCU, it represents a powerful tool for building GUI-centric HID applications.
Buck 3 click is a very advanced synchronous step-down (buck) converter, which is designed to deliver noise and ripple-free voltage to highly sensitive applications, such as FPGA and high-performance DSP platforms. The onboard step-down converter IC integrates low RDSON MOSFETs, that allow high efficiency, and thus high current on the output - up to 8A....
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
TFT Board 7 Resistive is a 7" display board which features the standardized 2x20-pin display connector. The display board also integrates a resistive touch panel. The TFT display module supports up to 24-bit pixel format (RGB: 888) and resolution of 800 x 480 pixels. It features an excellent contrast ratio and uniform brightness. TFT Board 7 Resistive,...
Pressure 10 Click features a digital interface barometric pressure sensor, based on piezoresistive bridge, labeled as HSPPAD042A, from ALPS Electric. It can use both SPI and I2C communication protocols, allowing it to be interfaced with a broad range of MCUs. Besides the pressure readings, this Click board™ also offers very accurate temperature reading,...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
for PIC32MZ CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 5 for PIC32MZ CAPACITIVE is not limited to multimedia-based applications only. USB, Ethernet, WiFi and RF connectivity options, digital motion sensor, battery charging functionality, piezo-buzzer,...
Battery Holder for CR2032 represents a unique battery holder (SN2032) that allows you to maintain good contact with the battery and facilitates simple replacement. This battery holder is suitable for a non-rechargeable (primary) coin-cell battery, CR2032 lithium coin cell battery (20mm diameter x 3.2mm thickness). The SN2032 comes with three mounting pads...
Accel 28 Click is a compact add-on board that contains an acceleration sensor. This board features the LIS2HH12TR, an ultra-low-power high-performance three-axis accelerometer from STMicroelectronics. It allows selectable full-scale acceleration measurements in ranges of ±2g, ±4g, and ±8g in three axes with a configurable host interface that supports both...
Compass 8 Click is a compact add-on board designed for precise compass applications. This board features the AK09919, a 3-axis electronic compass IC from AKM Semiconductor. The AK09919 is based on high-sensitivity Hall sensor technology for detecting terrestrial magnetism across the X, Y, and Z axes, has multiple operational modes, a built-in oscillator,...
Empty PSoC MCU Cards that enable you to solder different PSoC microcontrollers and other electronic components you need on them.
Loading
Load more
Loading
