Filter Product By
Slide and select filter/s
Filtered by
GNSS 6 Click is a compact add-on board that provides fast positioning capabilities. This board features the Teseo-LIV3FL, a tiny low-power GNSS module from STMicroelectronics. It is an easy-to-use global navigation satellite system that embeds the Teseo III single-die standalone positioning receiver, which can work simultaneously on multiple...
for STM32F4 CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 3 for STM32F4 CAPACITIVE is not limited to multimedia-based applications only. USB, digital motion sensor, battery charging functionality, SD card reader and much more expands its use beyond the...
ISM RX Click is a compact add-on board that contains a complete wireless RF digital data receiver. This board features the MAX1471, a low-power CMOS RF dual-channel receiver configurable through SPI serial interface from Analog Devices. It operates from both 3V or 5V and is designed to receive both amplitude-shift-keyed (ASK) and frequency-shift-keyed...
Temp&Hum 20 Click is a compact add-on board that represents temperature and humidity sensing solution. This board features the CC2D23, a highly accurate, fully-calibrated relative humidity and temperature sensor from Amphenol. This sensor, characterized by its high accuracy (±2% from 20% to 80%RH (±3% over entire humidity range)) and high resolution,...
Fusion for PIC32 v8 is a development board for PIC32 architecture devices. It contains many on-board modules necessary for device development, including multimedia, Ethernet, USB, and other.
LV-24-33 v6 100-pin TQFP 2 MCU Card Empty PCB
Heart rate 6 Click is an optical biosensor Click board™ designed for heart-rate monitoring (HRM). This Click board™ employs a specialized sensor that incorporates two LED drivers and photo-sensing elements which are the most sensitive to green light. The green light is most commonly used to measure the dilatation of the blood vessels, therefore Heart rate...
RS485 Isolator 4 Click is a compact add-on board designed for robust RS-485 and RS-422 half-duplex communication with galvanic isolation. This board features the ISO1450, a 5kVRMS isolated RS-485 transceiver from Texas Instruments. The ISO1450 supports data rates up to 50Mbps and features advanced protection against electrostatic discharge (ESD) and...
Tact Switch 6x6mm SMD Omron (10pcs)
MIC23099 click carries the MIC23099, a single AA/AAA cell step-down/step-up regulator with battery monitoring. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over the following pins on the mikroBUS™ line: CS, INT.
Light Ranger 3 click is an accurate distance measurement Click board™ based on a ToF (Time of Flight) measurement principle. The Simblee™ enabled RFD77402 rangefinder module from RF Digital is a complete measurement stack on the chip. It is surprisingly easy to work with, as this highly integrated range finder module exposes the only I2C interface and INT...
Pressure 16 Click is a compact add-on board that contains a board-mount pressure sensor. This board features the WSEN-PADS (2511020213301), a high-precision MEMS-based digital absolute pressure sensor from Würth Elektronik. It has a fully-calibrated 24-bit pressure output to provide accurate atmospheric pressure data with a configurable host interface...
UWB 2 Click is a compact add-on board that brings Ultra-Wideband communication to any solution. This board features the DWM3000, an IEEE 802.15-z UWB transceiver module from Qorvo. This module fully aligns with FiRaTM PHY, MAC, and certification development. It uses an integrated UWB antenna to establish wireless communication in UWB channels 5 (6.5GHz)...
GNSS RTK 3 Click is a compact add-on board that enhances the precision of position data derived from satellite-based positioning systems. This board features the LC29HDA, a dual-band, multi-castellation GNSS module from Quectel. This module supports the concurrent reception of all five global GNSS constellations: GPS, BDS, Galileo, GZSS, and GLONASS. It...
Charger 9 click is a Li-Ion (Li+, Li-Po) battery charger, capable of charging one, two or three battery cells. It is based on the MAX1757, an integrated Li+ battery charger with many features that allow safe and reliable charging. This IC has an internal switching-mode regulation with input current limiting, allowing it to use an external power supply...
pH Click Bundle - This bundle gives you everything you need to take high accuracy, interference-free pH readings. It allows users to combine pH Plastic Probe BNC with pH Click to read pH values with the same accuracy and capabilities as with some other solutions from AtlasScientific.
Click shield for Pi 400 Combine Raspberry Pi 400 with your favorite Click boards™ Start your project development with our Click Shield for Pi 400 fast and easy. The Raspberry Pi 400 combined with the mikroBUS™ and Shuttle socket provides you immediate access to hundreds of Click boards™ in our offer, allowing you to create a limitless number of...
Angle 7 Click is a compact add-on board that detects the absolute angular position of a permanent magnet. This board features the AS5600, a programmable Hall-based rotary magnetic position sensor with a high-resolution 12-bit analog or PWM output from ams AG. Based on planar Hall technology, this sensor measures the orthogonal component of the flux...
ISO ADC 7 Click is a compact add-on board designed for precise multi-channel data acquisition in various industrial applications. This board features the AMC131M03, a three-channel, 24-bit delta-sigma ADC from Texas Instruments. The AMC131M03 features a silicon-dioxide-based isolation barrier providing 5000-VRMS isolation, integrated digital decimation...
Standard empty MCU card for 100-pin TQFP Stellaris® 1000 series. Card is not populated with components. Pin distance 100mil.
Buggy is a robot rover platform expandable with all sorts of sensors and transceivers. A dream car for hackers and makers. Multiple kits available.
Nano Power 2 click is a very low power voltage comparator, aimed at portable and battery-powered applications. It allows detecting a difference of two voltage potentials, applied on two input pins. The device can detect differences very precisely, avoiding oscillations that can occur when both input voltages are equal by employing an internal hysteresis....
LDC1101 click is an inductance-to-digital converter Click Board™. It is designed for a range of different applications, based on the inductivity measurements. You can use it to detect the position, rotation, or motion of an object. LDC1101 carries the LDC1101, the integrated, high-resolution, high-speed, inductance-to-digital converter. The converter...
Clock Gen 5 Click is a compact add-on board that contains a digital programmable oscillator solution. This board features the LTC6903, a low-power self-contained digital frequency source providing a precision frequency from 1kHz to 68MHz set through a 3-wire SPI digital interface from Analog Devices. The LTC6903 features a proprietary feedback loop that...
Loading
Load more
Loading
