Filter Product By
Slide and select filter/s
Filtered by
Intel® Joule™ Click SHIELD + is an extension for Intel® Joule™ Expansion Board with four mikroBUS™ sockets. This click shield allows you to add more than 1600 Click boards™ to your project. Add displays, WiFi, ZigBee or Bluetooth transceivers, Ethernet modules, sensors, MP3 codec circuit and other features to your prototype with ease.
Battery Holder for CR2032 represents a unique battery holder (SN2032) that allows you to maintain good contact with the battery and facilitates simple replacement. This battery holder is suitable for a non-rechargeable (primary) coin-cell battery, CR2032 lithium coin cell battery (20mm diameter x 3.2mm thickness). The SN2032 comes with three mounting pads...
ATA6503 Click is a compact add-on board for high-speed CAN FD communication in automotive and industrial applications. This board features the ATA6503, a fully integrated CAN FD System Basis Chip (SBC) from Microchip, meeting Grade 0 AEC-Q100 standards. It supports both Classical CAN and CAN FD protocols with data rates up to 8Mbit/s, features an...
Empty PSoC MCU Cards that enable you to solder different PSoC microcontrollers and other electronic components you need on them.
Smart programmable touch display, packed with features. Mikromedia can be used as a powerful programmable dashboard control panel for both hobby projects, but also for the entire systems. Based on the powerful FT900 MCU, it represents a powerful tool for building GUI-centric HID applications.
Buck 3 click is a very advanced synchronous step-down (buck) converter, which is designed to deliver noise and ripple-free voltage to highly sensitive applications, such as FPGA and high-performance DSP platforms. The onboard step-down converter IC integrates low RDSON MOSFETs, that allow high efficiency, and thus high current on the output - up to 8A....
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
TFT Board 7 Resistive is a 7" display board which features the standardized 2x20-pin display connector. The display board also integrates a resistive touch panel. The TFT display module supports up to 24-bit pixel format (RGB: 888) and resolution of 800 x 480 pixels. It features an excellent contrast ratio and uniform brightness. TFT Board 7 Resistive,...
Pressure 10 Click features a digital interface barometric pressure sensor, based on piezoresistive bridge, labeled as HSPPAD042A, from ALPS Electric. It can use both SPI and I2C communication protocols, allowing it to be interfaced with a broad range of MCUs. Besides the pressure readings, this Click board™ also offers very accurate temperature reading,...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
for PIC32MZ CAPACITIVE Rapid development of multimedia and gui-centric applications BUILD GREAT GUI IN NO TIME Rich with peripherals Mikromedia 5 for PIC32MZ CAPACITIVE is not limited to multimedia-based applications only. USB, Ethernet, WiFi and RF connectivity options, digital motion sensor, battery charging functionality, piezo-buzzer,...
Empty PSoC MCU Cardsthat enable you to solder different PSoC microcontrollers and other electronic components you need on them.
Index Counter Click is a simple prototyping high precision Hall-Effect switch solution with direction detection. This board is hosting TLE4966K an integrated circuit dual Hall-effect sensor from Infineon. The sensor is designed specifically for highly accurate applications which use a rotating pole wheel since offers high sensitivity and high stability of...
Stepper 18 Click is a compact add-on board that contains a microstepping stepper motor driver. This board features the DRV8426, a stepper motor driver for industrial and consumer applications from Texas Instruments. It is fully integrated with two N-channel power MOSFET H-bridge drivers, a microstepping indexer, and integrated current sensing capable of...
1-Wire Switch Click is a compact add-on board that allows you to switch a device remotely using a 1-wire signal. This board features the DS2413, a dual-channel programmable I/O 1-Wire switch from Analog Devices. Communication and operation of this Click board™ are performed with the single 1-Wire serial interface, with the possibility of selecting signals...
Load Cell 8 Click is a compact add-on board representing a weigh scale solution. This board features the ZSC31050, an advanced differential sensor signal conditioner from Renesas designed for high-precision signal conditioning in applications requiring detailed sensor-specific corrections. It excels in processing differential sensor signals for various...
DAC 19 Click is a compact add-on board designed for high-performance voltage-output applications. This board features the DAC53701-Q1, a 10-bit automotive-grade DAC from Texas Instruments, offering smart functionality through force-sense output, GPI function trigger, PWM output, and integrated nonvolatile memory (NVM). The board supports an internal or...
EasyMx PRO v7 for Tiva C Series Empty MCU card for 100-pin TQFP TM4C123 series. Card is not populated with components. Pin distance 100mil.
Brushless 27 Click is a compact add-on board that controls DC brushless motors with any MCU. This board features the TMC6300, a power driver for BLDC/PMSM motors from Analog Devices. It is a highly efficient low voltage, zero standby driver for 3-phase BLDC/PMSM motors with up to 2A peak current. The triple half-bridge of this driver separates the HS and...
UT-S 7-SEG B 2 Click is a compact add-on board that presents an easy solution for adding a numeric or hexadecimal display to your application. This board features the TLC5947, a constant-current sink LED driver from Texas Instruments, alongside six ultra-thin blue single-digit numeric displays, the JSS-3011BUB-21. The displays are small in size (0.39...
MICRF TX Click is a compact add-on board designed as a powerful RF transmitter for data transmission over the 315MHz frequency band. This board features the MICRF112, a high-performance RF transmitter IC from Microchip, renowned for its efficiency in operation. This Click board™ stands out for its ease of use, requiring only a simple crystal oscillator to...
MCU Card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. By introducing the new MCU Card standard, we have ensured the absolute compatibility between the development board and any of the supported MCUs, regardless of their pin...
Charger 16 Click is a compact add-on board that represents a single-cell battery charger. This board features the LT1571, a constant-current/constant-voltage battery charger with preset voltage and termination flag from Analog Devices. Powering up from an external power supply rated up to 20V, this Click board™ has an onboard current sense resistor which...
Barometer 6 Click is a compact add-on board used to measure air pressure in a specific environment. This board features the 2SMPB-02E, a high-accuracy digital barometric air pressure sensor with low current consumption from Omron Electronics. The 2SMPB-02E has a calibration parameter for broader pressure and temperature range, features a MEMS chip for...
Loading
Load more
Loading
