Dear All,
I just got a new EasyMx PRO™ v7 for STM32.
I installed MikroC pro for ARM and MikroProg Suite For ARM on PC (Win 7), everything ok.
However, When I connect EasyMx PRO™ v7 for STM32 to PC to test some examples,
I open MikroProg Suite For ARM on PC
Detect MCU ok, Read MCU ok, I load examples from DVD and MikroE website to test development board, then write this to MCU but nothing happen after that.
Please give me advice to solve this.
Thank you for your help.
Trung Manh.
New EasyMx PRO™ v7 for STM32 can not test with all examples
-
- Posts: 5
- Joined: 17 Oct 2014 14:59
- petar.timotijevic
- mikroElektronika team
- Posts: 1739
- Joined: 19 Feb 2014 13:46
- Location: Serbia
- Contact:
Re: New EasyMx PRO™ v7 for STM32 can not test with all examp
Hi Trung Manh and welcome to the MikroE forum,
Please can you tell us with which specific example you have problem?
Did you properly configure development board according to specific example requirements?
Also please describe problem with more details.
Best regards,
Peter
Please can you tell us with which specific example you have problem?
Did you properly configure development board according to specific example requirements?
Also please describe problem with more details.
Best regards,
Peter
-
- Posts: 5
- Joined: 17 Oct 2014 14:59
Re: New EasyMx PRO™ v7 for STM32 can not test with all examp
Hi Peter,
Thank you so much for your reply.
I want to test some mikroC PRO for ARM examples from Mikroe DVD and Website such as Ledblinking.hex, button.hex, MP3.hex, TFT.hex...
However, for example, when I loaded a Ledblinking.hex into Mikro Suite for ARM then push write to MCU, the screen flashing very quick DISPLAY "programming" with red color and nothing happen then.
I already test with other examples,but the problem as the same.
I attached Config of Laptop, Config of MikroPlog and Config of STM32 Dev board.
Kindly advice something wrong.
Highly appreciated for your help.
Best regards
Trung Manh
Thank you so much for your reply.
I want to test some mikroC PRO for ARM examples from Mikroe DVD and Website such as Ledblinking.hex, button.hex, MP3.hex, TFT.hex...
However, for example, when I loaded a Ledblinking.hex into Mikro Suite for ARM then push write to MCU, the screen flashing very quick DISPLAY "programming" with red color and nothing happen then.
I already test with other examples,but the problem as the same.
I attached Config of Laptop, Config of MikroPlog and Config of STM32 Dev board.
Kindly advice something wrong.
Highly appreciated for your help.
Best regards
Trung Manh
- Attachments
-
- Capture of Labtop.PNG (27.38 KiB) Viewed 2687 times
-
- Capture of Config Mikroplog.PNG (112.2 KiB) Viewed 2687 times
-
- STM32.JPG (1.43 MiB) Viewed 2687 times
- petar.timotijevic
- mikroElektronika team
- Posts: 1739
- Joined: 19 Feb 2014 13:46
- Location: Serbia
- Contact:
Re: New EasyMx PRO™ v7 for STM32 can not test with all examp
Hi Trung Manh,
Please check that you program right HEX file.
Please set development board properly for ledblinking example, your board is not configured properly.
Please also always read note in commented section in source code.
Your photo shows photo on TFT display? TFT example works?
Best regards,
Peter
Your photo shows incorrectly board configuration for Ledblinking example. Please see photo in attachment what you need to set for LedBlinking example.Trung Manh wrote:I want to test some mikroC PRO for ARM examples from Mikroe DVD and Website such as Ledblinking.hex, button.hex, MP3.hex, TFT.hex...
However, for example, when I loaded a Ledblinking.hex into Mikro Suite for ARM then push write to MCU, the screen flashing very quick DISPLAY "programming" with red color and nothing happen then.
I already test with other examples,but the problem as the same.
I attached Config of Laptop, Config of MikroPlog and Config of STM32 Dev board.
Please check that you program right HEX file.
Please set development board properly for ledblinking example, your board is not configured properly.
Please also always read note in commented section in source code.
Your photo shows photo on TFT display? TFT example works?
Best regards,
Peter
- Attachments
-
- STM32 Configuration.JPG (236.82 KiB) Viewed 2674 times
-
- Posts: 5
- Joined: 17 Oct 2014 14:59
Re: New EasyMx PRO™ v7 for STM32 can not test with all examp
Dear Peter,
I am setting the development boards for LedBlinking example as your guide in photo, the ledBlinking examples is running ok.
I am highly appreciated for your help.
My problem is configure development board according to specific example requirements.
Kindly advice me all examples from MikroE do not have enclose guide to configure development boards?
Again, Thank you very much.
Best regards
Trung Manh
I am setting the development boards for LedBlinking example as your guide in photo, the ledBlinking examples is running ok.
I am highly appreciated for your help.
My problem is configure development board according to specific example requirements.
Kindly advice me all examples from MikroE do not have enclose guide to configure development boards?
Again, Thank you very much.
Best regards
Trung Manh
- petar.timotijevic
- mikroElektronika team
- Posts: 1739
- Joined: 19 Feb 2014 13:46
- Location: Serbia
- Contact:
Re: New EasyMx PRO™ v7 for STM32 can not test with all examp
Hi,Trung Manh wrote:Dear Peter,
I am setting the development boards for LedBlinking example as your guide in photo, the ledBlinking examples is running ok.
I am highly appreciated for your help.
My problem is configure development board according to specific example requirements.
Kindly advice me all examples from MikroE do not have enclose guide to configure development boards?
Again, Thank you very much.
Best regards
Trung Manh
Each code example has NOTES in commented section. Commented section is located on top in main example source code file. Notes describes how you need to set your development board.
Development board User Manual
http://www.mikroe.com/downloads/get/183 ... l_v102.pdf
Best regards,
Peter
-
- Posts: 5
- Joined: 17 Oct 2014 14:59
Re: New EasyMx PRO™ v7 for STM32 can not test with all examp
Dear Peter,
It seems better with EasyMx PRO™ v7 for STM32 now.
Thank you so much for your help.
Best regards
Trung Manh.
It seems better with EasyMx PRO™ v7 for STM32 now.
Thank you so much for your help.
Best regards
Trung Manh.