Click Boards

Just push your Click board into the innovative new mikroBUS™ standard socket and use it with zero hardware configuration! These boards will revolutionize the way you add new functionality to your development boards.

microSD click

Need more additional memory? We’ve got just the thing for you. microSD Click is an accessory board in mikroBus™ form factor. It features an microSD card slot for microSD cards used as a mass storage media for portable devices. Industry standard SPI interface ensures simple communication at high data rates. Use it for reading or storing data like music, text files, videos and more. Board is designed to use 3.3V power supply only.

microSD Click User Manual [398.67KB] microSD Click Examples [256.79KB] mikroBUS™ specification [142.87KB]

$16.00

Top

ADC click

ADC Click is an accessory board in mikroBus™ form factor. It includes a 12-bit Analog-to-Digital Converter (ADC) MCP3204 that features 50k samples/second, 4 input channels and low-power consumption (500nA typical standby, 2µA max). Board uses industry standard SPI communication interface. It is small in size and features convenient screw terminals for easier connections. Board is set to use 3.3V power supply by default. Place PWR SEL SMD jumper to 5V position if used with 5V systems.

ADC Click User Manual [447.37KB] ADC Click Examples [129.52KB] mikroBUS™ specification [142.87KB]

$24.00

Top

DIGI POT click

DIGIPOT Click is an accessory board in mikroBus™ form factor. It features a single-channel digital potentiometer MCP4161 with 8-bit resolution (256 wiper steps) and industry-standard SPI serial interface. The resistance value of the digital potentiometer goes up to 10 kΩ. It features outstanding AC/DC characteristics and low power consumption. It can be used in audio equipment, servo-motor control, battery charging and control, LCD contrast control, programmable filters etc.

DIGI POT Click User Manual [411.36KB] DIGI POT Click Examples [96.41KB] mikroBUS™ specification [142.87KB]

$16.90

Top

RS485 click 5V

RS485 Click 5V is an accessory board in mikroBus™ form factor. The on-board ADM485 differential line transceiver is suitable for high speed bidirectional data communication on multipoint bus transmission lines. It is designed for balanced data transmission and complies with EIA standards RS-485 and RS-422. This transceiver features a differential line driver and differential line receiver. Board operates on 5V power supply only.

RS485 Click 5V User Manual [419.34KB] RS485 Click Examples [111.42KB] mikroBUS™ specification [142.87KB]

$18.00

Top

MP3 Click

MP3 Click is an accessory board in mikroBus™ form factor. It includes a stereo MP3 decoder chip VS1053 which can decode multiple formats (Ogg vorbis, MP3, MP1, MP2, MPEG4, WMA, FLAC, WAW, MIDI), and encode three different formats from microphone in mono or stereo format (Ogg vorbis, IMA ADPCM, 16-bit PCM). Board uses industry-standard Serial Peripheral Interface for communication, and can only use 3.3V power supply. Board features stereo headphone and microphone audio connectors.

MP3 Click User Manual [453.53KB] MP3 Click Examples [356.92KB] mikroBUS™ specification [142.87KB]

$21.90

Top

Buzz Click

BUZZ Click is an accessory board in mikroBus™ form factor. Board features a piezo speaker capable of emitting audio signals. Buzzer’s resonant frequency is 3.8kHz (where you can expect it’s best performance). On-board buzzer driver is connected to both digital (CS) and to PWM line. You can use either of those two to provide the signal from the microcontroller to the buzzer driver. Board is set to use 5V power supply by default. Solder PWR SEL SMD jumper to 3.3V position if used with 3.3V systems.

Buzz Click User Manual [407.18KB] Buzz Click Examples [72.71KB] mikroBUS™ specification [142.87KB]

$9.00

Top

RTC Click

RTC Click is an accessory board in mikroBus™ form factor. It features the PCF8583 serial real-time clock (RTC). It is a low-power, full binary-coded decimal (BCD) clock/calendar. Board uses I2C interface for communication and features a 3V/230mA lithium battery as a backup power supply which ensures that timekeeping operation continues even when the main power supply goes OFF. Board is set to use 3.3V power supply by default. Solder PWR SEL SMD jumper to 5V position if used with 5V systems.

RTC Click User Manual [425.31KB] RTC Click Examples [153.17KB] mikroBUS™ specification [142.87KB]

$21.00

Top

RTC2 click

RTC2 Click is an accessory board in mikroBus™ form factor. It features the DS1307 serial real-time clock (RTC). It is a low-power, full binary-coded decimal (BCD) clock/calendar with programmable square-wave output signal. Board uses I2C interface for communication, and can only use 5V power supply. Board features a 3V/230mA lithium battery as a backup power supply which ensures that timekeeping operation continues even when the main power supply goes OFF.

RTC2 Click User Manual [422.55KB] RTC2 Click Examples [141.67KB] mikroBUS™ specification [142.87KB]

$21.00

Top

DAC Click

DAC Click is an accessory board in mikroBus™ form factor. It includes a 12-bit Digital-to-Analog Converter MCP4921 that features an optional 2x buffered output and SPI interface. The board provides high accuracy and low noise performance for industrial applications where calibration or compensation of signals, such as temperature, pressure and humidity, are required. Board is set to use 3.3V power supply by default. Solder PWR SEL SMD jumper to 5V position if used with 5V systems.

DAC Click User Manual [502.96KB] DAC Click Examples [156.22KB] mikroBUS™ specification [142.87KB]

$18.00

Top

SHT11 click

SHT11 Click is an accessory board in mikroBus™ form factor. It includes a digital humidity and temperature sensor SHT11. A unique capacitive sensor element is used to measure relative humidity while the temperature is measured by a band-gap sensor. Serial I2C interface and factory calibration, allow easy and fast system integration. Board is set to use 3.3V power supply by default. Solder PWR SEL SMD jumper to 5V position if used with 5V systems.

SHT11 Click User Manual [417.75KB] SHT11 Click Examples [194.22KB] mikroBUS™ specification [142.87KB]

$26.00

Top

EXPAND click

EXPAND Click is an accessory board in mikroBus form factor. It includes a 16-bit I/O expander MCP23S17 with SPI clock speeds up to 10 MHz for higher throughput applications. Three HARDWARE ADDRESS SEL jumpers allow you to configure board address and connect up to eight devices on the bus. Controller also supports interrupt-on-change feature. Board is set to use 3.3V power supply by default. Solder PWR SEL SMD jumper to 5V position if used with 5V systems.

EXPAND Click User Manual [491.00KB] Expand Click Examples [97.30KB] mikroBUS™ specification [142.87KB]

$12.00

Top

GPS Click

GPS Click is an accessory board in mikroBus™ form factor. It’s a compact solution for adding GPS functionality to your device. It fetures LEA-6S, high performance u-blox 6 positioning engine. Board can be interfaced with a microcontroller through UART or I2C connection, or data can be acquired using PC application through USB connection. Board features connector compatible with active and passive antennas. It can operate on 3.3V power supply only.

GPS Click User Manual [441.25KB] EasyGPS Examples [80.27KB] mikroBUS™ specification [142.87KB]

$49.00

Top

Bluetooth Click

BLUETOOTH Click is an accessory board in mikroBus™ form factor. Enrich your device with bluetooth capability with up to 100m range. Board offers low power, highly economic Bluetooth radio for adding wireless capability to your products. On-board RN-41 module with UART interface is easy and simple to use. Board is designed to use 3.3V power supply only.

Bluetooth Click User Manual [452.43KB] Bluetooth Click Examples [134.12KB] mikroBUS™ specification [142.87KB]

$41.90

Top

ETH Click

ETH Click is an accessory board in mikroBus™ form factor. It features ENC28J60, a 28-pin, 10BASE-T stand alone Ethernet Controller with an on-board MAC & PHY, 8K Bytes of Buffer RAM and SPI serial interface. Chip supports programmable automatic retransmit on collision and automatic rejection of erroneous packets. Board contains standard RJ-45 connector, transmit, receive and power LEDs. On-board crystal oscillator ensures stable operation. Board is designed to use 3.3V power supply only.

ETH Click User Manual [421.14KB] ETH Click Examples [140.64KB] mikroBUS™ specification [142.87KB]

$24.00

Top

BEE click

BEE Click is an accessory board in mikroBus™ form factor. It features 2.4 GHz IEEE 802.15.4 radio transceiver module MRF24J40MA. This module includes an integrated PCB antenna and matching circuitry and is connected to the microcontroller via a SPI interface. As such, this module is an ideal solution for wireless networks, smart home automation, building automation and other electronic applications that need wireless communication. Board is designed to use 3.3V power supply only.

Bee Click User Manual [452.19KB] Bee Click Examples [135.13KB] mikroBUS™ specification [142.87KB]

$29.00

Top

RS485 click 3.3V

RS485 Click 3.3V is an accessory board in mikroBus™ form factor. The on-board SN65HVD12 differential line transceiver is suitable for high speed bidirectional data communication on multipoint bus transmission lines. It is designed for balanced data transmission and complies with EIA standards RS-485 and RS-422. This transceiver features a differential line driver and differential line receiver. Board is set to use 3.3V power supply by default.

RS485 Click 3.3V User Manual [434.72KB] RS485 Click 3.3V Examples [128.58KB] mikroBUS™ specification [142.87KB]

$18.00

Top

LightHz click

LightHz Click is an accessory board in mikroBus™ form factor. Board features TSL230BR programmable light-to-frequency converter. The output can be either a pulse train or a square wave (50% duty cycle) with frequency directly proportional to light intensity. Device sensitivity is selectable in three ranges, providing two decades of adjustment. The full-scale output frequency can be scaled by one of four preset values. Board features voltage selection SMD jumper which determines whether it will operate on 5V or 3.3V power supply.

LightHz Click User Manual [430.91KB] LightHz Click Examples [102.27KB] mikroBUS™ specification [142.87KB]

$17.90

Top

CAN SPI click 3.3V

CAN SPI click 3.3V is an accessory board in mikroBus™ form factor. It is the best solution to add CAN connectivity to your microcontroller with SPI interface. Board features SN65HVD230 can transciever circuit which provides CAN serial communication physical layer in accordance with the ISO 11898 standard. It is designed for operation in especially-harsh environments, these devices feature cross-wire protection, loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range. Board is designed to use 3.3V power supply only.

CAN SPI click 3.3V User Manual [459.85KB] CAN SPI click 3.3V Examples [152.44KB] mikroBUS™ specification [142.87KB]

$21.00

Top

CAN SPI click 5V

CAN SPI click 5V is an accessory board in mikroBus™ form factor. It is the best solution to add CAN connectivity to your microcontroller with SPI interface. Board features MCP2551 can transciever circuit which provides CAN serial communication physical layer in accordance with the ISO 11898 standard. It is designed for operation in especially-harsh environments, these devices feature cross-wire protection, loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range. Board is designed to use 5V power supply only.

CAN SPI click 5V User Manual [461.03KB] CAN SPI click 5V Examples [133.95KB] mikroBUS™ specification [142.87KB]

$21.00

Top